Ranger 191 CAYMAN Скачать руководство пользователя | Manualshive

Страница: 24 / 78

background image

Your Livewell Aeration System

MAINTENANCE TIPS FOR AERATOR SYSTEM

(1) Remove screens only for flushing aerator system.
(2) Keep screens in place for cleaning and during operation. Replace

damaged or broken screens immediately.

(3) Do not exceed the recommended fuse size on the aerator pumps (a

larger fuse WILL NOT make a stronger aerator system!).

(4) Lubricate pivot on livewell control cable periodically using light weight

machine oil.

(5) Continual operation of pump (especially dry) will damage pump. Be

sure aerator switches are “off” when storing, etc.

TROUBLESHOOTING

Pump runs, but will not pump water:

➪

Entrapped air pocket around pump impeller has “air locked” pump.
With valve in “fill” position, back boat up slowly to expel entrapped
water.

➪

Grass, sticks, or other debris have clogged the filters or cavity
around the pump impeller, restricting water flow to pump. Clean
screens, or remove screens and flush system with garden hose
using moderate pressure.

Pump will not run (no “hum” is heard):

➪

Make sure switch is in the “Manual” position (in “Automatic” the
pump could be working, but in off time).

➪

Check master breaker switch in the rear compartment.

➪

Check fuse. Replace if necessary.

➪

Check wire connector at pump.

➪

Replace pump.

Livewells will not hold water in “Fill” position.

➪

Flush system to clear debris from livewell valve.

➪

Check cable to valve connection for proper adjustment.

➪

Remove cable, put water in livewell to see if well will hold water
with cable removed. If so, adjust cable to match actuator arm.

➪

Remove valve and disassemble. Clean inside of valve with warm
soapy water and inspect flappers for nicks, cuts and abrasions.
Replace flappers if necessary.

24

«
...
22
23
24
25
26
...
»

Содержание 191 CAYMAN















































































Отзывы:

Нет отзывов

Похожие инструкции для 191 CAYMAN

Бренд: Lagoon Страницы: 122

Бренд: J Страницы: 30

Fairline Phantom Flybridge Cruisers 46 -...

Бренд: FAIRLINE Страницы: 24

XL700 WaveRunner 2001

Бренд: Yamaha Страницы: 120

XL700 WaveRunner 2001

Бренд: Yamaha Страницы: 122

XLT1200 WaveRunner 2003

Бренд: Yamaha Страницы: 138

XLT800 WaveRunner 2002

Бренд: Yamaha Страницы: 140

XLT800 WaveRunner 2003

Бренд: Yamaha Страницы: 140

XLT1200 WaveRunner 2003

Бренд: Yamaha Страницы: 531

Бренд: Cresent Kayaks Страницы: 9

Бренд: Malibu Boats Страницы: 64

Бренд: Crivit Страницы: 43

Бренд: J/Boats Страницы: 36

Бренд: Skeeter Страницы: 194

Бренд: Polaris Страницы: 114

Бренд: WAV Страницы: 21

Бренд: Ocean Kayak Страницы: 5

Waverunner VXS VX1800

Бренд: Yamaha Страницы: 318

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды