background image

MINI TRACKED DUMPER

5

GB

on  the  unit.  Transporting  or  performing 
maintenance or service on a machine with its 
switch on invites accidents.

If  the  machine  should  start  to  vibrate 
abnormally,  stop  the  engine  (motor)  and 
check immediately for the cause. Vibration is 
generally a warning sign of trouble.

Engine Safety

This  machine  is  equipped  with  an  internal 
combustion  engine.  Do  not  use  on,  or  near, 
forest-covered or brush-covered land unless 
the exhaust system is equipped with a spark 
arrester  meeting  applicable  local,  state,  or 
federal laws.

In  the  state  of  California,  a  spark  arrester  is 
required by law. Other states have similar laws. 
A spark arrester, if used, must be maintained 
in effective working order by the operator.

Never start or run the engine inside a closed 
area.  The  exhaust  fumes  are  dangerous, 
containing carbon monoxide, an odorless and 
deadly  gas. Operate this  unit  only  in  a  well-
ventilated outdoor area.

Do not tamper with the engine in an effort to 
get it to run at higher speeds. The maximum 
engine  speed  is  preset  by  the  manufacturer 
and is within safety limits. See engine manual.

Keep  a  Class  B  fire  extinguisher  on  hand 
when operating this machine in dry areas as a 
precautionary measure.

Fuel Safety

Fuel is highly flammable, and its vapors can 
explode  if  ignited.  Take  precautions  when 
using to reduce the chance of serious personal 
injury.

When  refilling  or  draining  the  fuel  tank,  use 
an  approved  fuel  storage  container  while  in 
a  clean,  well-ventilated  outdoor  area.  While 
adding  fuel  or  operating  the  unit,  do  not 
smoke,  and  stay  away  from  sparks,  open 
flames, or other sources of ignition near the 
area  of  operation.  Never  fill  the  fuel  tank 
indoors.

To avoid sparking or arcing, keep grounded 
conductive  objects  –  such  as  tools  –  away 
from  exposed,  live  electrical  parts  and 
connections. These events could ignite fumes 
or vapors. 

Always stop the engine and  allow  it  to cool 
before  filling  the  fuel  tank.  Never  remove 
the cap of the fuel tank or add fuel while the 
engine is running or when the engine is hot. 
Do not operate the machine with known leaks 
in the fuel system.

Loosen the fuel tank cap slowly to relieve any 
pressure in the tank. 

Never  overfill  the  fuel  tank.  Because  engine 
heat can cause fuel to expand, never fill the 
tank to more than 1/2” below the bottom of 
the filler neck. This will provide space for fuel 
expansion.

Replace  all  fuel  tank  and  container  caps 
securely  and  wipe  up  spilled  fuel.  Never 
operate the unit without the fuel cap securely 
in place.

Avoid creating a source of ignition for spilled 
fuel. If fuel is spilled, do not attempt to start 
the engine. Instead, move the machine away 
from the area of spillage and avoid creating 
any source of ignition until fuel vapors have 
dissipated.

When  fuel  is  spilled  on  yourself  or  your 
clothes,  wash  your  skin  and  change  clothes 
immediately.

Store fuel in containers specifically designed 
and approved for fuel storage.

Store fuel in a cool, well-ventilated area, safely 
away  from  sparks,  open  flames,  or  other 
sources of ignition.

Never  store  fuel  –  or  a  machine  with  fuel  in 
the tank – inside a building where fumes may 
reach a spark, open flame, or any other source 
of ignition (such as a water heater, furnace, or 
clothes dryer). Allow the engine to cool before 
storing in any enclosure.

Содержание RR560

























Отзывы: