background image

MINI TRACKED DUMPER

12

GB

Operation

No oil in the engine originally,  but 
a  bottle  of  engine  oil  is  in  scope 
of  delivery.  Don’t  start  the  engine 
before adding oil.

DO  NOT  OVERFILL.  Check  engine 
oil level daily and add as needed.

Gasoline  is  highly  flammable  and 
explosive.  You  can  be  burned  or 
seriously injured when handling fuel. 
Use  extreme  care  when  handling 
gasoline.

Fill  the  fuel  tank  outdoors,  never 
indoors. Gasoline vapors can ignite 
if  they  collect  inside  an  enclosure. 
Explosion can result.

IMPORTANT: DO NOT OVERFILL!

This  equipment  and/or  its  engine 
may  include  evaporative  emissions 
c o n t r o l   s y s t e m   c o m p o n e n t s , 
r e q u i r e d   t o   m e e t   E P A   a n d /
or  CARB  regulations,  that  will 
only  function  properly  when  the 
fuel  tank  has  been  filled  to  the 
recommended  level.  Overfilling 
may  cause  permanent  damage 
to  evaporative  emissions  control 
system  components.  Filling  to 
the  recommended  level  ensures 
a  vapor  gap  required  to  allow  for 
fuel  expansion.  Pay  close  attention 
while filling the fuel tank to ensure 
that  the  recommended  fuel  level 
inside the tank is not exceeded. Use 
a  portable  gasoline  container  with 
an  appropriately  sized  dispensing 
spout when filling the tank. Do not 
use  a  funnel  or  other  device  that 
obstructs the view of the tank filling 
process.

Never use choke to stop engine.

Clutch Control Lever

Squeeze  the  control  lever,  clutch  engaged. 
Release the lever, clutch disengaged.

Make sure the power trackbarrow is on a 
flat, level surface.

Open the fuel shut-off valve.

 

Move the engine switch to the ON position.

Using a funnel, add oil up to the FULL mark 
on the dipstick. (See engine manual for oil 
capacity, oil recommendation, and location 
of fill cap.)

Reinstall the fuel cap and tighten. Always 
clean up spilled fuel.

Remove the oil fill cap/dipstick to add oil.

1. 

2. 

1. 

3. 

3. 

2. 

Add Oil To Engine

Add Gasoline To Engine

CLOSED

OPEN

Starting Engine

ON

OFF

ON

OFF

The engine must be off and allowed to cool 
at least two minutes before adding fuel.

Remove the fuel filler cap and fill the tank. 
(See engine manual for fuel capacity, fuel 
recommendation, and location of fuel cap.)

1. 

2. 

Содержание RR560

























Отзывы: