Raisecom RC3000 PCM Скачать руководство пользователя

Страница: 49 / 86

Raisecom Technology Co., Ltd

offered, and when you need to transfer balanced interfaces to unbalanced ones

RC909-4E1 of Raisecom is available.

c. Optical interface:

SC connector is for optical interface. And if you are not sure of Rx & Tx direction,

please connect the connector before device powered on.

d. Connect network management interface:

When this device is connected with network management PC, connect cable to

LINK UP interface; and when you need network management cascade, connect

cable to LINK DOWN interface. Please connect to network management interface

before device powered on if you are not sure of common grounding.

8.3.3. Powered

on:

a. Verify all the connections are normal (power supply and interfaces), and than

powered on.

b. Verify the self-check of the device is normal (PWR is ON and SYS is flicking).

Buzzer will buzz if there are alarms and MUTE botton can shutdown present

alarm sound.

c. You do not need to configure the device for point-to-point topology. Use

CONSOLE interface to configure the device when necessiry.

d. RC3000 will work normally if all connections are right.

Содержание RC3000 PCM























































































Результаты поиска

Содержание RC3000 PCM

Отзывы:

Похожие инструкции для RC3000 PCM

Бренды по названию

Популярные бренды

Raisecom RC3000 PCM, Руководство пользователя

Результаты поиска

Содержание RC3000 PCM

Отзывы:

Похожие инструкции для RC3000 PCM

Бренды по названию

Популярные бренды