Raisecom RC3000 PCM Скачать руководство пользователя

Страница: 42 / 86

Raisecom Technology Co., Ltd

7.8. RC3000-SUB-DETH user-board explanation

7.8.1. Rules of channel distribution:

RC3000-SUB-DETH is an Ethernet data user card with a 10BaseT interface, and

please refer to configuration rules of RC3000-SUB-DV35 user card.

7.8.2. Ethernet interface definition

Ethernet interface uses RJ45 connector and can realize MDI & MDIX cable as following

figure:

Indicatore lights are all green:

LNK: indicates the Ethernet user card LINK status, ON means link

PWR: power supply indicator light, ON means powered on.

ACT: ON transmitting data

FDX: ON full dulplex

Ethernet interface standard compliant.

7.8.3. Ethernet data card configuration explanation

Ethernet user card has many functions and both Hyper Terminal and network

management can configure the following commands:

a. Configuration of user card time slot; b. Choose the data channel; c.

Buffer configuration

d. Default interface mode e. Interface reset

Please refer to Appendix A How to use Hyper Terminal to configure RC3000

7.9. RC3000-SUB-D232 user-board explanation:

RC3000-SUB-D232 serail data user-board has standard RS232 interface. There are 8

channels whitch is decided by hardware, unchangeable. Four RC45 connectors make up

of the 8 channels and each RJ45 connector has two channels. And the definition of each

Figure 32

Содержание RC3000 PCM























































































Результаты поиска

Содержание RC3000 PCM

Отзывы:

Похожие инструкции для RC3000 PCM

Бренды по названию

Популярные бренды

Raisecom RC3000 PCM, Руководство пользователя

Результаты поиска

Содержание RC3000 PCM

Отзывы:

Похожие инструкции для RC3000 PCM

Бренды по названию

Популярные бренды