Raisecom iTN2100 Скачать руководство пользователя страница 56

Страница: 56 / 312

Raisecom
iTN2100 (P100R002) Hardware Description

5 NMS card

Raisecom Technology Co., Ltd.

LED

Status

Description

100M

(NM-EXT)

Green

NM-EXT interface rate LED



Green: the Ethernet rate is 100 Mbit/s.



Off: the Ethernet rate is 10 Mbit/s.

LNK/ACT

(NM-EXT)

Green

NM-EXT interface working LED



Green: the NM-EXT interface is working properly.



Off: the NM-EXT interface is disconnected or is
working improperly.



Blinking green: the NM-EXT interface is receiving or
sending data.

5.1.6 Alarms

Table 5-6 lists alarms of the iTN2100-NMS.

Table 5-6

Alarms of the iTN2100-NMS

Alarm

Cause

Level

Chassis alarm



The NMS channel between a card and the NMS card fails.



The SDH clock module fails.

Critical

Cold reset

The iTN2100 is reset upon power failure.

Critical

5.1.7 Specifications

Table 5-7 lists specifications of the iTN2100-NMS.

Table 5-7

Specifications of the iTN2100-NMS

Parameter

Value

Dimensions

25 mm (width) × 232 mm (depth) × 240 mm (height)

Weight

≤ 0.43 kg

Max. power consumption 10 W

Содержание iTN2100

























































































































































































































































































































Результаты поиска

Содержание iTN2100

Отзывы:

Бренды по названию

Популярные бренды

Raisecom iTN2100, Описание аппаратуры

Результаты поиска

Содержание iTN2100

Отзывы:

Бренды по названию

Популярные бренды