manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 263

Raisecom 
iTN2100 (P100R002) Hardware Description 

20 Service aggregation cards 

 

 

Raisecom Technology Co., Ltd. 

234 

 

20.2 iTN2100-8SU-S 

20.2.1 Appearance and functions 

Appearance 

Function 

 

The iTN2100-8SU-S card can be used to multiplex or de-multiplex 8 CWDM wavelength 
optical signals. The 8-wavelength CWDM system can efficiently use the bandwidth of the 
fiber to prevent laying fibers repeatedly. This helps save costs. The 8 wavelength channels 
are 1471 nm, 1491 nm, 1511 nm, 1531 nm, 1551 nm, 1571 nm, 1591 nm, and 1611 nm. 

 

Support multiplexing/de-multiplexing 8 CWDM standard wavelength channels (1471 
nm, 1491 nm, 1511 nm, 1531 nm, 1551 nm, 1571 nm, 1591 nm, and 1611 nm). Each 
wavelength channel can be used to multiplexing/de-multiplexing optical signals. 

 

Be applied to dual-fiber and single-fiber CWDM network, providing flexible 
networking applications. 

 

Plug and play. The card is available for services after being inserted into 6-U chassis and 
being properly connected with fibers, without being configured. 

 

Work properly after power off. The internal passive optical module in the card works 
properly after the card is powered off. Therefore, ensure that the card can finish 
multiplexing/de-multiplexing of optical wavelength. 

 

Support the NView NNM system, helping view card configurations. 

 

Support transmitting services transparently, bringing no limit on the speed and frame 
format of the accessed optical signals. 

 

Consume less power, without configuring the fan. 

 

20.2.2 Slots 

The iTN2100-8SU-S can be plugged into slots 1–5 and 8–12 on the iTN2100. 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды