manualshive.com logo in svg

Raisecom iTN2100, Описание аппаратуры

Поделиться
Скачать
Raisecom iTN2100 Скачать руководство пользователя страница 247

Raisecom 
iTN2100 (P100R002) Hardware Description 

19 Multi-service cards 

 

 

Raisecom Technology Co., Ltd. 

218 

 

LED 

Status 

Description 

SYS 

Green 

System status LED 

 

Green: the system is down or fails. 

 

Off: the CPU is working improperly. 

 

Blinking green: the system is working properly. 

FXS FXO 

V24 RS485 

Green 

If the 4 LEDs are in green, it indicates that the MULTI-
FXS, MULTI-FXO, MULTI-V24, and MULTI-RS485 
are inserted into the iTN2100. 

IN-USE 1–8 

Green 

Indicate the usage status of the voice channel. The LED 
is lighten up for local off-hook (outputting signaling), 
local ringing (inputting signaling), and conversation. It 
indicates that the voice channel is being used. 

IN-USE13–16 

Green 

Indicate the usage status of the data channel. The LED is 
in blinking green when the data is being received or sent. 
The blinking frequency is related to the data frequency. 

 

19.2.5 DIP Switch 

Table 19-18 lists the DIP switch on the OPCOM3500E-MULTI. After the DIP switch is 
configured by the software, default configurations of the DIP switch are invalid. 

Table 19-18

 

DIP switch on the OPCOM3500E-MULTI 

Service 

BIT of 

SW1 

Description 

Function 

ON 

OFF (default) 

Voice interface 
configuration 

1 

Configure polarity 
inversion of FXS interfaces. 
Note that polarity inversion 
configured through the 
software is invalid. 

Supported 

Unsupported 

2/4W interface 
configuration 

2 

Configure 2/4W interface 
modes. 

2-wire mode 

4-wire mode 

3–5 

Set the default gain value 
(providing 4 commonly-
used values). 

Gain value 
configuration 
(A-D/D-A) 

SW1.3 

SW1.4 

SW1.5 

0/0 

OFF 

OFF 

OFF 

0/-3.5 

OFF 

OFF 

ON 

+14/+4 

OFF 

ON 

OFF 

+16/+7 

OFF 

ON 

ON 

Data interface 
configuration 

6 

Configure V.24 interface 
modes. 

Synchronous (V.24) 

Asynchronous 
(RS232) 

Содержание iTN2100

























































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды