RadiSys PL35Q Скачать руководство пользователя страница 32

Страница: 32 / 72

Hardware Reference

PS/2 mouse and keyboard

With the Winbond® W83627DHG Super I/O controller, the Q35 motherboards support the PS/
2 keyboard and mouse interfaces on the rear I/O panel.

Mouse and keyboard features include:

8042-based keyboard controller with support for PS/2 mouse and keyboard

Fast Gate A20 and hardware keyboard reset

User options for the clock frequency of 6, 8, 12, and 16MHz via the BIOS setup utility
configuration.

Super I/O

The Winbond W83627EHG Super I/O controllers is capable of supporting a wide range of I/O
functions with the LPC (Low Pin Count) interface. The Q35 motherboards support the following
legacy devices via this super I/O chip:

UART ports (

page 31

)

PS/2 mouse and keyboard (

page 32

)

Note:

Though the W83627EHG super I/O chip is capable of supporting 40 GPIO lines by itself,

these GPIO lines are unavailable on the Q35 motherboards.

Expansion interfaces

IDE

The Q35 motherboard provide a standrd IDE connector to support IDE hard disks and ATAPI
devices via the ICH9‘s PCI controller.

PCI

PCI slots are compliant with the

PCI Local Bus Specification Version 2.3

. The PL35Q

motherboard has one 32-bit, 33MHz, 3.3V PCI slot.

PCI Express

All PCI Express interfaces on the PL35Q motherboard are compliant with the

PCI Express Base

Specification Version 1.1

One PCI Express x16 graphics interface

One PCI Express x4 interface

One PCI Express x1 interface.

Содержание PL35Q









































































Результаты поиска

Содержание PL35Q

Отзывы:

RadiSys PL35Q, Руководство по эксплуатации продукта, Страница: 32 / 72

Результаты поиска

Содержание PL35Q

Отзывы: