RadiSys PL35Q Скачать руководство пользователя страница 30

Страница: 30 / 72

Hardware Reference

Audio

The Q35 motherboards support:

Intel High Definition Audio using the Realtek ALC883 eight-channel stereo CODEC

Triple 3.5mm audio jacks on the rear I/O panel for surround sound.

One 1x4-pin CD-ROM header to support onboard sound for audio CD playback

Note:

An onboard PC speaker is not provided, but it is recommended that you connect an

external speaker to the front panel I/O header to hear the beep signals.

Network

The PL35Q motherboard has a single Gigabit Ethernet controller.

Ethernet port 0 uses the Intel 82566DM PHY controller, which connects to the ICH9/ICH9DO
LAN (the MAC integrated on the ICH9/ICH9DO chipset) through a dedicated interconnect.

Ethernet features include:

Standard IEEE 802.3 Ethernet interface for 10BASE-T, 100BASE-TX, and 1000BASE-T
applications (802.3, 802.3u, and 802.3ab)

Remote boot and PXE via BIOS configuration

Wake-On-LAN support via BIOS configuration with the option to use the native operating
system, as well as support for legacy operating systems

Onboard RJ45 connector with 2 integrated programmable LEDs showing link speed and
speed.

Table 21. Ethernet LEDs

LED color

LED state

Ethernet link and activity

Green/Amber

Off

10Mbps link speed

Green steady on

100Mbps link speed

Amber steady on

1000Mbps link speed

Yellow

Off

No link established

Yellow steady on

Link established; communication activity not detected

Yellow blinking

Link established; communication activity detected

Содержание PL35Q









































































Результаты поиска

Содержание PL35Q

Отзывы:

RadiSys PL35Q, Руководство по эксплуатации продукта, Страница: 30 / 72

Результаты поиска

Содержание PL35Q

Отзывы: