RadiSys PL35Q Скачать руководство пользователя страница 27 | Manualshive

Страница: 27 / 72

RadiSys PL35Q Скачать руководство пользователя страница 27

3

Chipset

27

I/O Controller Hub

The Intel ICH9 and ICH9DO I/O provide extensive I/O support:

Direct Media Interface (DMI) support for chip-to-chip connection between the GMCH and
ICH

PCI Express Base Specification, Revision 1.1 support

PCI Local Bus Specification, Revision 2.3 support for 33 MHz PCI operations

ACPI Power Management Logic Revision 3.0b support

Enhanced DMA controller, interrupt controller, and timer functions

Integrated Serial ATA host controllers with independent DMA operation up to six ports and
AHCI support

USB host interface with support for up to 12 USB ports, 6 UHCI host controllers, and 2 EHCI
high-speed USB 2.0 host controllers

Integrated 10/100/1000 Mbps Gigabit Ethernet MAC with system defense

System Management Bus (SMBUs) Specification, Revision 2.0 with additional support for
I2C devices

Intel High Definition Audio support

Intel Matrix Storage Technology support

Intel Active Management Technology support (ICH9 Digital Office only)

Intel Virtualization Technology for directed I/O support

Intel Trusted Execution Technology support

Low Pin Count (LPC) interface support

Firmware Hub (FWH) interface support

Serial Peripheral Interface (SPI) support

Intel Quiet System Technology support

For further information, refer to the

Intel 3 Series Express Chipset Family Datasheet for the Intel

82Q35 Graphics and Memory Controller Hub

.

«
...
25
26
27
28
29
...
»

Содержание PL35Q









































































Отзывы:

Нет отзывов