Radiopost TS401 Скачать руководство пользователя страница 66

Страница: 66 / 70

■

Warranty

1 YEAR LIMITED WARRANTY

Warranty Period

Radiopost Inc. (Radiopost RC) warranties that the Products purchased (the “Product”)

will be free from defects in materials and workmanship for a period of 1 year from the

date of purchase by the Purchaser.

Limited Warranty

(b) Limitations

‐

RADIOPOST MAKES NO WARRANTY OR REPRESENTATION, EXPRESS

OR IMPLIED, ABOUT NON

‐

INFRINGEMENT, MERCHANTABILITY OR FITNESS FOR A

PARTICULAR PURPOSE OF THE PRODUCT. THE PURCHASER ACKNOWLEDGES THAT

THEY ALONE HAVE DETERMINED THAT THE PRODUCT WILL SUITABLY MEET THE

REQUIREMENTS OF THE PURCHASERS INTENDED USE.
(c) Purchaser Remedy

‐

Radiopost's sole obligation hereunder shall be that Radiopost

will, at its option, (i) repair or (ii) replace, any Product determined by Radiopost to be

defective. In the event of a defect, these are the Purchaser's exclusive remedies.

Radiopost reserves the right to inspect any and all equipment involved in a warranty

claim. Repair or replacement decisions are at the sole discretion of Radiopost. This

warranty does not cover cosmetic damage or damage due to acts of God, accident,

misuse, abuse, negligence, commercial use, or modification of or to any part of the

Product. This warranty does not cover damage due to Improper installation, operation,

maintenance, or attempted repair by anyone other than Radiopost. Return of any

goods by Purchaser must be approved in writing by Radiopost before shipment.

(a) This warranty is limited to the original Purchaser ("Purchaser") and is not

transferable. REPAIR OR REPLACEMENT AS PROVIDED UNDER THIS WARRANTY IS THE

EXCLUSIVE REMEDY OF THE PURCHASER. This warranty covers only those

Products purchased from an authorized Radiopost dealer located in the US & Canada.

Third party transactions are not covered by this warranty. Proof of purchase is required

for warranty claims. Further, Radiopost reserves the right to change or modify this

warranty without notice and disclaims all other warranties, express or implied.

Damage Limits:

RADIOPOST SHALL NOT BE LIABLE FOR SPECIAL, INDIRECT OR CONSEQUENTIAL

DAMAGES, LOSS OF PROFITS OR PRODUCTION OR COMMERCIAL LOSS IN ANY WAY

CONNECTED WITH THE PRODUCT, WHETHER SUCH CLAIM IS BASED IN CONTRACT,

WARRANTY, NEGLIGENCE, OR STRICT LIABILITY. Further, in no event shall the liability

of Radiopost exceed the individual price of the Product on which liability is asserted.

As Radiopost has no control over use, setup, final assembly, modification or misuse,

no liability shall be assumed nor accepted for any resulting damage or injury. By the

act of use, setup or assembly, the user accepts all resulting liability. If you as the

Purchaser or user are not prepared to accept the liability associated with the use of

this Product, you are advised to return this Product immediately in new and unused

condition to the place of purchase, please contact your dealer for specific return

policies.

Содержание TS401







































































Результаты поиска

Содержание TS401

Отзывы:

Похожие инструкции для TS401

Бренды по названию

Популярные бренды

Radiopost TS401, Руководство пользователя

Результаты поиска

Содержание TS401

Отзывы:

Похожие инструкции для TS401

Бренды по названию

Популярные бренды