Radiopost TS401 Скачать руководство пользователя страница 42

Страница: 42 / 70

5.11 Brake

This function is used to operate the brake system of front wheels and the

brake system of rear wheels separately. The brake of rear wheels can be

connected to the Ch. 2 and the brake of front wheels can be connected

to the Ch. 3 or Ch. 4. Brake mixing can be applied to Ch. 3 and Ch. 4

respectively. If the mixing function is inhibited (INH), the value setting

cannot be done and will be blocked by the mark „---„.

The default setting for this function is INH. Move to the channel to

be set using the

LEFT

and the

RIGHT

in the Mode. Press the

SET

to change the mode into ACT using the

RIGHT

and press the

SET

again to activate the selected channel. The figure below shows that

Ch. 3 is activated.

■

How to Set

Move to the RATE-EACH using the

DOWN

to set the mixing ratio.

The range of mixing ratio is 0 to 100. The default value is 100.

Move to the RATE-COM using the

DOWN

to set the mixing ratio.

The range of mixing ratio is 0 to 100. The default value is 100. As

the RATE-COM setting affects Ch. 4, it is used to apply the brake

mixing ratio both to Ch. 3 and Ch. 4.

Содержание TS401







































































Результаты поиска

Содержание TS401

Отзывы:

Похожие инструкции для TS401

Бренды по названию

Популярные бренды

Radiopost TS401, Руководство пользователя

Результаты поиска

Содержание TS401

Отзывы:

Похожие инструкции для TS401

Бренды по названию

Популярные бренды