background image

i

Use the garage door operator only: 

 to open and close garage doors

 for private use

 according to the instructions and safety  

  regulations in this manual
Any other use shall be regarded as non-compliant 
with the intended use.

Correct use of the hand transmitter

The remote control via hand transmitter is only admis-

sible for appliances and equipment in which radio 

interference in the transmitter or receiver does not 

present a hazard for persons, animals or property or 

for which the risk is covered by other safety equipment.

 Only operate the garage door operator in dry rooms. 

 The garage door must be able to be opened and  

  closed easily by hand and must not jam.

Proper use

Operating conditions

i

 Ensure that the overhead ceiling tracks are always  

  free of grease and dirt. Dirty overhead ceiling tracks  

  hinder proper operation.  

  A 220 - 240 V/50 - 60 Hz power supply must be avail- 

  able at the place of installation.

Comply with all maintenance intervals

Proper use also includes the regular inspection of the 

door and its safety equipment.

Failing to observe all of the information con-

tained in this manual can lead to severe per-

sonal injury, e.g. by being trapped by the door.

Pay attention to all of the information. In order to comply  

with the safety regulations in standards EN 13241-1,   

EN 12445 and EN 12453, it is particularly important that  

this operating and assembly manual is followed during the 

installation process.

i

Safety instructions

Opener service life is 25.000 cycles.

Each steel wire rope shall have a safety fac-

tor not smaller than 6 (minimum breaking 

strength / static load of one rope). 

Rope drums shall have a pitch circle diameter 

(PCD) at least equal  to 20 times the rope 

diameter.

Important safety instructions. 

It is important for the safety of persons to follow all 

instructions. Save these instructions.

7

EN

Содержание RolloPort S2





































Отзывы: