Quark-Elec QK-G033, Руководство пользователя

Страница: 20 / 23

Quark-elec Manual
https://www.quark-elec.com 20 of 23 2018
V1.52
mode information in the following format:
‘ MMMM1MMMM2’ , where MMMM could be
INCH or SELF. INCH refers to Latching
control mode (relay will act for 3 seconds and
then revert to the normal position), and SELF
refers to Self-lock mode.
For example, INCH1SELF2 means, relay 1
works in Latching control mode and relay 2
works in Self-lock mode.
Check relay working
status
WHOACTIVE G033 will reply with the relay working status
information similar to the following
format:
‘ R1, R2, R3: ACTIVE; DEACTIVE; ACTIVE. ’
Where ACTIVE means the related relay has
been triggered (COM port connected to NO
port),
DEACTIVE means the related relay is on the
normal status.
One-off relay switch
toggling
ONOFFRnxxx#
n=1, Relay 1; n=2, Relay 2.
xx range from 001 to 999,
indicating the delay time in
seconds.
*From Aug 2018, this
command has changed to
be ‘
ONOFFRnxxx#’
; this
allows the maximum time
can be 999 seconds.
For example, by receiving ONOFFR175# , the
first relay (Relay 1) will be triggered on for 75
seconds and then switched off, whether G033
is working in Latching mode or in Self-lock
mode. G033 will reply with the relay information
in the following format:
‘ Port 1 is ON and will be OFF 75 seconds
afterwards‘
.
This is a one-off command, only valid for one
time action. The APP does not support this
command, so the operator should use SMS to
send this message.
433 MHz RF module (discontinued)
Switching RF module ON ONRFn
n=1 for 1 st RF terminals
n=2 for 2 nd RF terminals
n=3 for 3 rd RF terminals
n=4 for 4 th RF terminals
G033 will reply with the relay state information
in the following format:
‘RFn socket is ON’ , where n is the RF
terminal number.
Switching RF module
OFF
OFFRFn
n=1,1 st RF terminals;
n=2, 2 nd RF terminals;
n=3, 3 rd RF terminals;
n=4, 4 th RF terminals
G033 will reply with the relay state information
in the following format:
‘RFn socket is OFF’ , where n is the RF
terminal number.
Timer
Set time on G033 SThhmmss#
Where hhmmss is the
current time
For example, by sending ’ST153000# ’, the
operator set G033 time as 15:30:00. G033 will
return the message ‘ Time setup successful’
to accept this setting. If the operator sends the
wrong time format, G033 will return the
message ’Time setup failed’.
Check the local time on
G033
DQSJ By sending ‘ DQSJ’ , the operator will receive
the local time. The message received would be
‘ Time at terminal is 12:30:32’.
Set Switching Relays ON
time
ONnhhmmss
n=1, Relay 1
n=2, Relay 2
hhmmss is the Switch ON
time.
For example, by sending ‘ ON2163000 ’, the
operator set Switch Relay 2 ON at 16:30:00.
Message as ‘ Port 2 will switch ON’ will be
returned to operator if the setting successful.
Set Switching Relays
OFF time
OFnhhmmss
n=1, Relay 1
n=2, Relay 2
hhmmss is the Switch OFF
time.
For example, by sending ‘OF2194500’ , the
operator set Switch Relay 2 OFF at 19:45:00.
Message as ‘Port 2 will switch OFF’ will be
reply to operator if the setting successful.