background image

Chapter 3: Basic System Operations

Upgrading Firmware

StorNext M660 Metadata Appliance  Hardware Guide

63

Components and Upgrade Time Estimates

For All Firmware Upgrades

• Full access to all GUI features are not available during the upgrade. 

The GUI should not be started until the upgrade is complete.

For StorNext 5 and Later Upgrades

• The upgrade is applied to each node in reverse order, beginning 

with the secondary node. When the secondary node has completed 

its upgrade, the system will failover from the primary to the 

secondary, and begin upgrading the primary system. While the node 

firmware upgrade is being applied, metadata operations are not 

interrupted. Access to a limited StorNext GUI is available on the 

MDC node acting as primary during the upgrade of the node acting 

as secondary.

• Both MDC nodes will need to reboot after the metadata array 

firmware update is applied.

Note:

As of StorNext 5 Release 5.1.1, MDC node reboots after 

metadata array firmware updates are no longer required.

For Upgrades Prior to StorNext 5

• Each StorNext firmware update requires a reboot of both nodes. In 

some cases, multiple reboots of the nodes are required.

Component

Upgrade Time Estimate (approx. minimum)

MDC node

30 to 60 minutes per node*

Metadata Array

20 minutes**

* Reboot times could vary widely, depending on the size of the SAN in 

your environment, whether or not MDC node firmware needs to be 

upgraded, and the StorNext Release installed prior to the upgrade.
** Since metadata array operations, and the StorNext file system will 

be suspended during the array firmware upgrade, this is a 

downtime 

upgrade

.

Note:

See sections below for information on additional reboots that 

may be required for specific StorNext Releases.

Содержание StorNext M660























































































Отзывы: