background image

 

 

 

3. Commissioning 

 

1)  Remove the lid and fill the water tank with water (see water level gauge outside). 

 

      Never operate the unit with a liquid level beneath the lowest water level mark      
      

“min”!

 

 
2)  Connect the water pipes, check for possible leaks. 

 

3)  The  unit  is  designed  to  operate  with  a  tank  temperature  control  kit  which  includes  a 

submersible pump and plastic tubes to lead Glycol water through it. The fittings on the lid 
of the  unit  should  be  used  to  connect the  plastic  tubes.  Such kits  are  not  provided  with 
the unit. If used, please connect them according to the instructions of the manufacturer.  

 

4)  Close the lid. 

 

 

            Do not operate the unit when it is open with the lid removed!

 

 

 

5)  Establish the electric network connection (see 1.5 Electrical installation) 

 

6)  Adjust the required temperature on the thermostat (see 5. temperature setting). After    
      reaching the adjusted set-point temperature the unit is ready for operation (see also 1.1     
      safety measures).

 

        
 

3.1 Connection 

Verify that all connections are sealed. No dirt particles may gain access into the pipes and 
the cooling water in the unit.   
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

Содержание GLY401













Отзывы: