Quadro Quadro6L Скачать руководство пользователя страница 7

Страница: 7 / 57

Quadro6L/4L Manual I: Installation Guide

Requirements

Requirements

•

One 120/240 VAC power outlet in close proximity to the Quadro.

•

One RJ45 Ethernet 10/100 broadband Internet connection.

•

At least one RJ11 telephone connection is recommended to connect the Quadro to
the PSTN network.

•

At least one IP phone with an RJ45 connector connected to the Quadro WAN port
directly or through a hub or switch.

•

One CAT 5 Ethernet cable with an RJ45 connector to connect to the Quadro LAN
port.

•

One PC with a 10/100 Mbps Ethernet card or adapter installed.

•

TCP/IP network protocol installed on each PC.

•

For optimal results, Internet Explorer 5.5 or higher, or Netscape Navigator 4.7 or
higher are recommended.

Please Note:

The Quadro6L/4L is shipped with one RJ11 cable and one straight RJ45

CAT 5 cable. If the LAN connector of the Quadro connects to a hub or switch, a crossover
cable may be required.

Quadro6L/4L; (SW Version 5.2.x)

Содержание Quadro6L


























































Результаты поиска

Содержание Quadro6L

Отзывы:

Похожие инструкции для Quadro6L

Бренды по названию

Популярные бренды

Quadro Quadro6L, Руководство пользователя

Результаты поиска

Содержание Quadro6L

Отзывы:

Похожие инструкции для Quadro6L

Бренды по названию

Популярные бренды