background image

13

Fully Open Front 

FIG 83

Option #2

           

FIG 83a

FIG 83b

push front bow 

to back

Using Your Complete Soft Top-

Continued
Option #2

 

Fully Opened Driver and 

Passenger Sunroof  

 

For the next position you will need 

to slide the two side straps towards 

the header as shown in fig 83a and 

push the front bow in the center of the 

folded back “sunroof” and tuck/ fold it 

under the header, which opens up  the  

“sunroof”  completely  (FIG83b).This 

option is shown in Fig 83.

Option #3 & #4
Open over the front driver and pas-

senger compartments: 

          

T

hese options open both the front cab 

and rear cab portions of the top.  This 

option requires you to remove the 

front header arms and the two bows 

from the bow mount brackets. Fig 84 

shows the finished look of this “Sun 

Roof” option with the front header 

installed on the third bow bracket 

mount and the header folded  all the 

way back to the rear of the vehicle. 

With the header latches un-latched 

and front sec-tion open, un-hook the 

2 quick release knobs locat-ed on the 

end of the header arms as circled in 

Fig 84a.  Next, un-hook the 4 quick 

release knobs on bow #1 and bow #2 

(Fig’s 84c, 84d 84e) leaving the two 

rear bows (Bow #1 & #2) encased in 

the hook and loop flaps (Fig 84f, 84g). 

Once The front bow arms and two 

rear bows are disconnected from the 

bow mount brackets, with the help of 

a friend, carefully fold back the front 

header and two bows layering the top 

and bows under the fabric (Fig 84f) 

and then connect the front bow arms 

quick release brackets to the rear-

most third bow mount bracket.  This 

is option # 3. Notice in Fig’s.85, 85a & 

85b (page 14) how the fabric is “lay-

ered” back and the front Bow Mount 

Brackets are installed to the rear bow 

brackets.  

Also notice in Fig 85a how the side 

bow straps are pulled up completely 

towards the front header. This is op-

tion #4 with the entire fabric assembly 

folded  back and  secured  to  the  rear  

brackets.

Option #3

Partially Open rear 

(protects rear passenger from sun)

                 

FIG 84

front bow

         

FIG 84a

FIG 84b

FIG 84c

FIG 84d

Center bow #1

  

Center bow #2

FIG 84e

FIG 84f

front bow

         

                                                   

Center 
bow #1

 

Center 

bow #2

FIG 84g

Содержание QuadraTop 11113.2435

















Отзывы: