Quadra-Fire PELLET INSERT CB1200MI-MBK Скачать руководство пользователя

Страница: 27 / 32

October 9, 2017

7014-285A

CB1200 Pellet Insert

NOTE

: A Quadra-Fire outside air kit; 811-0872, is available

through your Quadra-Fire Dealer.

Mobile Home Installation

You must use a Quadra-Fire Outside Air Kit

811-0872 for installation in a mobile home.

1. An outside air inlet must be provided for the combustion air and

must remain clear of leaves, debris, ice and/or snow. It must

be unrestricted while the appliance is in use to prevent room

air starvation which causes smoke spillage. Smoke spillage

can also set off smoke alarms.

2. The combustion air duct system must be made of metal. It

must permit zero clearance to combustible construction and

prevent material from dropping into the inlet or into the area

beneath the dwelling and contain a rodent screen.

3. The appliance must be secured to the mobile home structure

by bolting it to the floor (using lag bolts). Use the same holes

that secured the appliance to the shipping pallet.

4. The appliance must be grounded with #8 solid copper ground

ing wire or equivalent, terminated at each end with an NEC

approved grounding device.

5. Refer to Clearances to Combustibles and floor protection

requirements on

page 8

for listings to combustibles and appro-

priate chimney systems.

6. Use silicone to create an effective vapor barrier at the loca-

tion where the chimney or other component penetrates to the

exterior of the structure.

Follow the chimney manufacturer’s instructions when installing

the vent system for use in a mobile home.

8. Installation shall be in accordance with the Manufacturers Home

& Safety Standard (HUD) CFR 3280, Part 24.

Spark Arestor Cap

Roof Flashing

Storm Colla

Joist Shield/Firestop

Double Wall

Connector Pipe

Figure 27.1

CAUTION

THE STRUCTURAL INTEGRITY OF THE MOBILE HOME

FLOOR, WALL AND CEILING/ROOF MUST BE MAINTAINED

Do NOT cut through:

• Floor joist, wall, studs or ceiling trusses.

• Any supporting material that would affect the structural

integrity.

This appliance is to be connected to a factory-built chimney

conforming to CAN/ULC-S629, Standard for 650°C Facto-

ry-Built Chimneys.

For removal of the chimney for mobile home transportation,

contact the proper transportation officials.

CAUTION

Never draw outside combustion air from:

• Wall, floor or ceiling cavity

• Enclosed space such as an attic or garage

WARNING

It is critical to have a working smoke detector installed in

the home of appliance operation.

•

Smoke alarms that are properly installed and maintained

play a vital role in reducing fire deaths and injuries. Having

a working smoke alarm reduces the chance of fire related

injuries..

WARNING

Products of combustion generate carbon monoxide and

different fuels generate different levels. Carbon monoxide

•

Only use approved fuels in this appliance.

•

Always keep door shut during operation. Operating this

appliance with doors open can allow CO to leak into the

home.

CO can kill you before you are aware it is in your home. At

lower levels of exposure, CO causes mild effects that are often

mistaken for the flu. These symptoms include headaches,

dizziness, disorientation, nausea and fatigue. The effects of CO

exposure can vary greatly from person to person depending

on age, overall health and the concentration and length of

exposure.

NEVER INSTALL IN A SLEEPING ROOM.

WARNING

Содержание PELLET INSERT CB1200MI-MBK

































Результаты поиска

Содержание PELLET INSERT CB1200MI-MBK

Отзывы:

Похожие инструкции для PELLET INSERT CB1200MI-MBK

Бренды по названию

Популярные бренды

Quadra-Fire PELLET INSERT CB1200MI-MBK, Руководство по установке

Результаты поиска

Содержание PELLET INSERT CB1200MI-MBK

Отзывы:

Похожие инструкции для PELLET INSERT CB1200MI-MBK

Бренды по названию

Популярные бренды