Quadra-Fire PELLET INSERT CB1200MI-MBK Скачать руководство пользователя

Страница: 5 / 32

October 9, 2017

7014-285A

CB1200 Pellet Insert

Reciprocating Saw

Channel Locks

Hammer

Phillips Screwdriver

Tape Measure

Plumb Line

1/4” Self-Tapping Screws

Framing Material

Hi-temp Caulking Material

Gloves

Safety Glasses

Framing Square

Electric Drill & Bits (1/4”)

Level

May also need:

Vent Support Straps

Venting Paint

Tools and building supplies normally required

for installation, unless installing into an existing

masonry fireplace:

C. Tools And Supplies Needed

B. Thermostat Wall Control Location

The thermostat wall control’s location will have some affect

on the appliance’s operation.

• Maximum wire length from appliance is 100 feet (30.48m)

continuous non-spliced wire. Recommended 20 gauge

wire, solid copper

•

When located close to the appliance, it may require a

slightly higher temperature setting to keep the rest of the

house comfortable.

•

When located

in an adjacent room or on a different floor

level, you will notice higher temperatures near the appli-

ance.

D. Inspect Appliance and Components

•

Open the appliance and remove all the parts and articles

packed inside the Component Pack. Inspect all the parts

and glass for shipping damage.

• Report to your dealer any parts damaged in shipment.
•

All labels have been removed from the glass door.

• Plated surfaces have been wiped clean with a soft cloth,

if applicable.

• Read all the instructions before starting the installation.

Follow these instructions carefully during the

installation to ensure maximum safety and benefit.

• Follow pipe manufacturer instructions for installation

and air clearance requirements.

WARNING

Fire Risk.

Damaged parts could impair safe operation. Do

NOT install damaged, incomplete or substitute

components.

WARNING

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be voided

by, the following actions:

• Installation and use of any damaged appliance.

• Modification of the appliance.

• Installation other than as instructed by Hearth & Home

Technologies.

• Installation and/or use of any component part not

approved by Hearth & Home Technologies.

• Operating appliance without fully assembling all

components.

• Operating appliance without legs attached (if supplied

with appliance).

• Do NOT Over fire

Or any such action that may cause a fire hazard.

Содержание PELLET INSERT CB1200MI-MBK

































Результаты поиска

Содержание PELLET INSERT CB1200MI-MBK

Отзывы:

Похожие инструкции для PELLET INSERT CB1200MI-MBK

Бренды по названию

Популярные бренды

Quadra-Fire PELLET INSERT CB1200MI-MBK, Руководство по установке

Результаты поиска

Содержание PELLET INSERT CB1200MI-MBK

Отзывы:

Похожие инструкции для PELLET INSERT CB1200MI-MBK

Бренды по названию

Популярные бренды