Quadra-Fire EXPLRMED-PBK Скачать руководство пользователя страница 15

December 3, 2015 

 

 

 

           7061-197I 

 

 

 

         

                  15

Explorer II Medium Wood Stove

Figure 15.2 - Floor Installation

B. Outside Air Kit Installation 

A source of air (oxygen) is necessary in order for combus-
tion to take place.  Whatever combustion air is consumed 
by the fi re must be replaced.  Air is replaced via air leakage 
around windows and under doors. In homes that have tightly 
sealed doors and windows, an outside air source is needed. 
An optional Outside Air Kit is available. 

Included in OAK-ACC: 

Termination cap, (2) wire ties, flex 
adapter, and fasteners

Items Needed for Installation (not supplied)

 • 4 inch fl ex aluminum pipe, or if using alternate material, 

then it shall be made from durable, non-combustible, 
heat resistant material up to 350

o

F.  Cut the pipe to the 

required length for your installation. 

  • Phillips head screw driver 

 • 

Silicone 

sealant

  • Drills and saws necessary for cutting holes through the 

wall or fl ooring in your home.

1.  Remove all materials from packing box.

2.  Using a #2 Phillips screw driver attach the fl ex adapter to 

the stove using 4 screws.  

Figure 15.1 & 15.2 

3

.

 

Floor & Rear Installation:

  Cut a 4 inch (102mm) hole in 

outside wall or fl oor to accommodate outside air piping.  
Use 4 inch (102mm) aluminum metal fl ex or rigid piping 
to directly connect outside air to appliance intake.  Use 
the supplied termination cap with a rodent screen.  Seal 
between the wall (or fl oor) and the pipe with silicone to 
prevent moisture penetration. 

WARNING

Fire Risk.   Asphyxiation Risk. 

Do not draw outside combustion air from:

• Wall, 

fl oor or ceiling cavity

•  Enclosed space such as an attic or garage

•  Close proximity to exhaust vents or chimneys

Fumes or odor may result

Asphyxiation Risk.

Outside air inlet must be located to prevent blockage 
from:

•  Leaves        •  Snow or ice       •  Other debris

Block may cause combustion air starvation

Smoke spillage may set off alarms or irritate sensitive individuals.

WARNING

Asphyxiation Risk.

Length of outside air supply duct shall NOT exceed the 
length of the vertical height of the exhaust fl ue.

• 

Fire will not burn properly

  Smoke spillage occurs when door is opened due to air star-

vation

WARNING

Figure 15.1 - Rear Installation

Содержание EXPLRMED-PBK





















Отзывы: