Quadra-Fire Adventure-II Скачать руководство пользователя

Страница: 6 / 32

Listing and Approval Codes

The Quadra-Fire Adventure-III Series Wood Burning Appli-

ance meets the U.S. Environmental Protection Agency’s

crib wood emission limits for wood heaters sold after May

15, 2015.

Model:

Adventure III

Laboratory:

Underwriter’s Laboratories, Inc.

Report No:

MH 60687

Type:

Solid Fuel Room Heater

Standard:

UL1482-10 and ULC S627-00
and (UM) 84-HUD, Mobile Home
Approved.

EPA Certification #: 1001-15

EPA Certified Emissions: 2.9 grams per hour

*LHV Tested Efficiency: 75.5%

**HHV Tested Efficiency: 70%

***EPA BTU Output: 11,200 to 43,300 / hr.

****Peak BTU/Hour Output: 98,100

Vent Size: 6 inches

Firebox Size: 4.5 cubic feet

Recommended Log Length: 22 inches

Fuel Seasoned Cord Wood

* Weighted average LHV (Low Heating Value) efficiency using

Douglas Fir dimensional lumber and data collected during EPA

emission test. LHV assumes the moisture is already in a vapor

state so there is no loss in energy to vaporize.

Weighted average HHV (High Heating Value) efficiency using

Douglas Fir dimensional lumber and data collected during EPA

emission test. HHV includes the energy required to vaporize the

water in the fuel.

***

A range of BTU outputs based on EPA Default Efficiency and

the burn rates from the low and high EPA tests, using Douglas

Fir dimensional lumber.

****

A peak BTU out of the appliance calculated using the maxi-

mum first hour burn rate from the High EPA Test and the BTU

content of cordwood (8600) times the efficiency.

•  Installation and use of any damaged appliance.
•  Modification of the appliance.
•  Installation  other  than  as  instructed  by  Hearth  &  Home

Technologies.

• Installation and/or use of any component part not approved by

Hearth & Home Technologies.

• Operating appliance without fully assembling all components.
• Do NOT Overfire - If appliance or chimney connector glows,

you are overfiring.

Any such action that may cause a fire hazard.

A. Appliance Certification

NOTE: Hearth & Home Technologies, manufacturer of

this appliance, reserves the right to alter its products,

their specifications and/or price without notice.

NOTE: This installation must conform with local codes. In the

absence of local codes you must comply with the UL1482, (UM)

84-HUD and NPFA211 in the U.S.A. and the ULC S628-93

and CAN/CSA-B365 Installation Codes in Canada.

C. Manufactured Housing Approved

•

This appliance is approved for manufactured hous-

ing installations when not installed in a sleeping

room and when an outside combustion air inlet is

provided.

•

The structural integrity of the manufactured housing

floor, ceiling, and walls must be maintained.

•

The appliance must be properly grounded to the

frame of the manufactured housing with #8 copper

ground wire, and chimney must be listed to UL103

HT or a listed UL-1777 full length six inch (152mm)

diameter liner must be used.

•

Outside Air Kit, part OAK-ADV must be installed in a

manufactured housing installation.

Improper installation, adjustment, alteration, service or

maintenance can cause injury or property damage.

For assistance or additional information, consult a qualified

installer, service agency or your dealer.

Quadra-Fire is a registered trademark of Hearth & Home

Technologies.

WARNING

Fire Risk.

Hearth & Home Technologies disclaims any

responsibility for, and the warranty will be voided by,

the following actions:

B. BTU & Efficiency Specifications

D. Glass Specifications

This appliance is equipped with 5mm ceramic glass.

Replace glass only with 5mm ceramic glass. Please con-

tact your dealer for replacement glass.

This appliance needs periodic inspection and repair for

proper operation. It is against federal regulations to oper-

ate this appliance in a manner inconsistent with operating

instructions in this manual.

Quadra-Fire • Adventure-III Owner’s Manual • 4083-900 • Rev D • 09/15

►

Содержание Adventure-II

































Результаты поиска

Содержание Adventure-II

Отзывы:

Похожие инструкции для Adventure-II

Бренды по названию

Популярные бренды

Quadra-Fire Adventure-II, Руководство пользователя

Результаты поиска

Содержание Adventure-II

Отзывы:

Похожие инструкции для Adventure-II

Бренды по названию

Популярные бренды