Quadra-Fire Adventure-II Скачать руководство пользователя страница 19

Страница: 19 / 32

Baffle & Blanket

Optional Fan

Chimney System

Firebrick & Ash Removal

Door & Glass Assemblies

Door Handle

Frequency

MONTHLY

After Every

Cord of Wood

Baffle and blanket placement is critical to

heat output, efficiency and overall life of the

appliance. Make sure the baffle is pushed

all of the way to the back of the firebox and

the blanket is laying flat. Inspect baffle for

cracks.

YEARLY

After Every

4 Cords of

Wood

Vacuum the fan impellers.

EVERY 2

MONTHS

After Every

4 Cords of

Wood

The chimney and chimney cap must be in-

spected for soot and creosote every two

months during the burn season or more fre-

quently if chimney exceeds or is under 14-16 ft

(4.3m-4.8m) measured from bottom of appli-

ance.
This will prevent pipe blockage, poor draft,

and chimney fires.
Always burn dry wood to help prevent cap

blockage and creosote build-up.

WEEKLY

After Every

25 Loads of

Wood

WEEKLY

After Every

25 Loads of

Wood

Keep door and glass gasket in good shape

to maintain good burn times. To test: place a

dollar bill between the appliance and door and

then shut the door. If you can pull the dollar

out, remove one washer from door handle

behind latch cam and try again. If you can still

pull it out, replace the door gasket.

Check the glass frame for loose screws to

prevent air leakage. Check glass for cracks.

WEEKLY

After Every 25

Loads of Wood

Check the door latch for proper adjustment.

This is very important especially after the door

rope has formed to the appliance face.
Check door handle for smooth cam operation.

Task

Blanket

Baffle

Ashes must be cool before you can dispose

of the ashes in a non-combustible container.
Firebrick is designed to protect your firebox.

After ashes are removed, inspect the fire-

brick and replace firebricks that are crum-

bling, cracked or broken.

A. Quick Reference Maintenance Guide

When properly maintained, your appliance will give you

many years of trouble-free service.

Contact your dealer

to answer questions regarding proper operation, trou-

bleshooting and service for your appliance. Visit www.

quadrafire.com to find a dealer.

CAUTION!

Allow the appliance to completely cool

down before performing any cleaning or maintenance.

Start the first inspection after the first 2 months of use, or

if performance changes, and adjust your schedule accord-

ingly. Maintenance is required for safe operation and must

be performed to maintain your warranty.

These are generic drawings and may not represent your model.

Maintenance and Service

Locknut

Latch Cam

Square Key

Quadra-Fire • Adventure-III Owner’s Manual • 4083-900 • Rev D • 09/15

Содержание Adventure-II

































Результаты поиска

Содержание Adventure-II

Отзывы:

Похожие инструкции для Adventure-II

Бренды по названию

Популярные бренды

Quadra-Fire Adventure-II, Руководство пользователя

Результаты поиска

Содержание Adventure-II

Отзывы:

Похожие инструкции для Adventure-II

Бренды по названию

Популярные бренды