QSC touchmix-30 pro, Руководство пользователя, Страница: 60 / 146

51
1001108-01-F
Output Channels
Output Channel – Overview
Provides a single-screen view of frequently used
controls and indicators for the output channel.
1. Overview tab – Selects the Channel
Overview screen.
2. Preset – Shows the currently selected Preset
for this channel.
3. Pick-off point – (Auxes only) Determines
where the signal for the output channel is taken.
4. Delay – Controls and indicates the amount of
delay (up to 100 msec.) applied to the signal.
5. Delay In – Applies / bypasses the delay.
6. Reset – Sets all controls for the input channel
to the factory default position.
7. Description of the Current Preset
8.
DCA – Indicates which DCA groups are
assigned to the channel.
9. Mute – Indicates which Mute groups control the
channel.
10. Parametric EQ Graph – A graphic
representation of the equalization curve based
on the EQ settings. When the EQ is engaged, the
trace becomes brighter.
• EQ Graph Vertical Scale –
Represents audio level from -20 dB to +20 dB.
• EQ Graph Horizontal Scale –
Represents frequency from 20 Hz to 20 kHz.
11. EQ Out/In – Engages / disengages the equalizer for the channel.
12. EQ Handles – Touch, hold, and drag to change the Frequency and Gain of the associated EQ band. The frequency band button
must be engaged to see the EQ Handles.
13. Aux Sends – (TouchMix-30 Pro only)
• Aux sends 9 – 14 are available for Aux Outputs 1 – 8 only,
• Displays the system numbers and user-defined names for the Aux channels.
• Adjustable sliders send signal to the associated Aux channel output.
• Mute indicates if the channel’s send to an Aux is muted or not.
14. Low and High Cut Filter and Frequency Bands 1, 2, 3, and 4 – These buttons engage or disengage the
associated filter.
To adjust the following parameters, select the field then use the Master encoder or the up/down nudge buttons on a mobile device.
15. Gain, Bands 1, 2, 3, and 4 – Displays and adjusts gain (-15 to +15 dB) for the selected frequency band.
16. Low and High Cut Filter Frequency – Displays and adjusts the knee frequency for the high and low cut filters.
17. Frequency Bands 1–4 frequency adjustment fields – Displays and adjusts the center frequency for the four
parametric EQ bands.
NOTE: The following section can be a Compressor or Limiter depending on the Comp/Limit switch on the Comp/Limiter tab.
18. Comp –
• Comp – Engages or disengages the channel’s compressor.
• Threshold – Displays and sets the level at which compression begins.
• Attack – Displays and sets the rate at which the compressor reaches its maximum compression when the threshold level is exceeded.
• Release – Displays and sets the rate at which the compressor ceases gain reduction when signal drops below threshold.
• Ratio – Displays and sets the amount of compression applied to the signal.
Home
Select an
Output
Bank
Select
Channel
Select
Overview
Tab
∞
3
4
5
6
1
2
Inputs 1-8
Cue
Aux
1
10
5
u
5
10
20 0
40
10
Main
L/R
10
5
u
5
10
20
0
40
10
Anti-
Feedback
Limiter
(Comp)
Auxes Presets Setup PEQ
Comp
Threshold
Attack
Release
Ratio
M
M
M
M
M
M
9
10
11
12
13
14
Aux 9
Aux 10
Aux 11
Aux 12
Aux 13
Aux 14
AUX Sends
GEQ
GR
LR
1 2
3 4
5 6
7 8
Default
E10 Monitor
Main
Cue
Main Mix
L/R
Scene:
Reset In
Joe’s Ears
Aux 1
Aux 2
Aux 2
Aux 3
Aux 3
Aux 4
Aux 4
Aux 5
Aux 5
Aux 6
Aux 6
Aux 7
Aux 7
Aux 8
Aux 8
Aux 9
Aux 9
Aux 10
Aux 10
Aux 11
Aux 11
Aux 12
Aux 12
Aux 13
Aux 13
Aux 14
Aux 14
20
10
0
-10
-20
20K 10K 5K 2K 1K 500 200 100 50 20Hz
3 4 2 1
0.00 0.00 0.00 0.00
120 80.0 400 2.0k 6.0k 8.0k
20
10
0
-10
-20
PEQ
Tuned for QSC E10 Monitor 1 2 3 4 5 6 7 8 DCA 1 2 3 4 5 6 7 8 Mute Groups
Preset E10 Monitor Pre Fdr Post Fdr Delay
ms
0.00
-12.0
16.0
50.0
4.0
Overview
Mute Mute
Aux 1 Overview
Pre Dyn Pre All
Out In
C
AF
L
F
Aux Out 1-8
2 3
1
6
8
5
7 9
4
11 10
14
16
17
15
13
18
12
Prev Next
2
1
4
3
5 6