QNAP ES2486dc Скачать руководство пользователя страница 46

Страница: 46 / 65

Specify the static IP address of the management port of each controller.
Example:

• LAN IP block:

10.8.13.xx

• Controller 1 IP address:

10.8.13.62

• Controller 2 IP address:

10.8.13.78

10.

Click

Proceed

A confirmation message appears.

Warning

Clicking

Confirm

deletes all data on the drive before installing QES.

11.

Click

Confirm

The wizard installs QES and restarts the NAS.

Note

You must initialize any unused disks upon your next login.

Installing QES Using a Dynamic IP Address

Warning

Installing QES deletes all data on the drives. Back up your data before proceeding.

Power on the NAS.

Connect the NAS to your local area network.

Run Qfinder Pro on a computer that is connected to the same local area network.

Tip

To download Qfinder Pro, go to

https://www.qnap.com/utilities

Locate the NAS in the device list.

Tip

Refer to the device type and MAC address to identify the NAS. The device status is a question
mark (

If the computer is connected to the NAS through the management port, Qfinder Pro will also display the
the details of Controller B.

Double-click an uninitialized controller.
The setup wizard opens.

Click

Quick Setup

The

Quick Setup

window opens.

Specify a NAS name and password.

ES2486dc User Guide

Installation and Configuration

Содержание ES2486dc


































































Результаты поиска

Содержание ES2486dc

Отзывы:

Похожие инструкции для ES2486dc

Бренды по названию

Популярные бренды

QNAP ES2486dc, Руководство пользователя

Результаты поиска

Содержание ES2486dc

Отзывы:

Похожие инструкции для ES2486dc

Бренды по названию

Популярные бренды