
37
36
STORAGE
Your gas bottle must be stored outdoors in a well ventilated area and must be disconnected from your
gas grill when not being used. Ensure that you are outdoors and away from any sources of ignition
before attempting to disconnect your gas bottle from your gas grill.
When you are using your gas grill after a period of storage, please ensure to check for gas leaks and
check for any obstructions in the burner etc. before using. Also follow the cleaning instructions to
ensure gas grill is safe.
If gas grill is stored outdoors ensure to check that all areas under the front panel are free from any
obstructions (insects etc.) This area must be kept free as this may affect the flow of combustion or ven-
tilation air.
CLEANING AND MAINTENANCE
Maintenance is recommended that every 90 days for your gas grill, but it is absolutely
necessary to perform maintenance at least once a year. By doing so, you will extend the life of your gas
grill.
Your gas grill is easy to clean with minimum effort, just follow these helpful hints for cleaning conve-
nience.
4
TROUBLESHOOTING
Emergencies
Possible cause
Prevention/ Solution
Gas leaking from
cracked/cut/burned
hose
Damaged hose.
Turn off gas at LP tank, if hoes is cut or
cracked, replace hose.See LP tank lead
test and connection regulator to the LP
tank.
Gas leaking from LP
tank
Mechanical failure due to resting or
mishandling.
Turn off LP tank valve.
Gas leaking from LP
tank valve
Failure or tank valve from mishandling
or mechanical failure.
Turn off LP tank valve. Return LP tank
to gas supplier.
Gas leaking
between LP tank
and regulator
connection
Improper installation, connection not
tight, failure of rubber seal.
Turn off LP tank valve, remove
regulator from cylinder and visually
inspect rubber seal for damage, see LP
tank test and connection regulator to
the LP tank.
Fire coming
through control
panel
Fire in burner tube section of burner
due to partial blockage.
Turn off control knobs and LP tank
valve. After fire is out and grill is cold,
remove burner and inspect for spider
nests or rust. see natural hazard and
cleaning the burner assembly pages.
Troubleshooting:
Problem
Possible cause
Prevention/ Solution
Grease fire
or continuous
excessive flames
above cooking
surface
Too much grease buildup in burner
area.
Turn off LP Tank. Leave lid open
to allow flames to die down. After
cooling, clean food particles and excess
grease from inside firebox area, grease
cup/pan/tray, and other surfaces.
Burner will not light
using ignitor
Gas issues
1.Trying to light wrong burner.
2. Burner not engaged with control
valve.
3. Obstruction in burner.
4. No gas flow.
5. Vapor lock at coupling nut to
LP tank.
6. Coupling nut ad LP tank valve not
fully connected.
1. See instructions on control panel
and section in the Usage Methods.
2. Make sure valve are positioned
inside of burner tubes.
3. Ensure burner tubes are not
obstructed with spider webs or other
matted, see cleaning section of use
and care.
4. Make sure LP tank is not empty. If
LP tank is not empty, refer to
“sudden drop in gas flow.
5. Turn off knobs and disconnect
coupling nut from LP tank.
Reconnect and retry.
6. Turn the coupling nut approximately.
Burner will not light
using ignitor
Electrical issues:
1. Electrode cracked or broken;”
sparks at crack.”
2. Electrode tip not in proper position
3. Wire and/or electrode covered with
cooking residue.
4. Wires are loose or disconnected.
5. Wires are shorting (sparking)
between igitor and electrode.
6. Push button sticks at bottom
sparking between ignitor and
electrode.
1. Replace electrode.
2. Tip of electrode should be pointing
toward port hole in burner. The
distance should be 1/8” to 3/16”.
Adjust if necessary.
3. Clean wire and or electrode with
rubbing alcohol and clean swab.
4. Reconnect wires or replace
electrode/wire assembly.
5. Replace ignitor wire.
6. Replace ignitor.
7. Inspect wire insulation and proper
connection. Replace wires if
insulation is broken.
4
Содержание OKG 102
Страница 2: ...OKG 102 OKG 103 OKG 104...
Страница 34: ...67 66...