Python Responder LC Model 991 Скачать руководство пользователя страница 56

Страница: 56 / 64

Table of zones

When using the Diagnostic functions, use the Table of Zones to see which input
has triggered the system. It is also helpful in deciding which input to use when
connecting optional sensors and switches.

ZONE NO.

TRIGGER TYPE

INPUT DESCRIPTION

Trunk Input

BLUE (H1/7)

Shock Sensor

Onboard shock sensor

Door Trigger

GREEN (H1/8) and VIOLET (H1/6).

Sensor 2

Optional MUX sensor port

Ignition

Heavy gauge pink of remote start harness

Hood Trigger

GRAY on the 6-pin shutdown harness.

Note:

The WarnAway® response does not report on the LED

Shutdown diagnostics

To perform shutdown diagnostics:

With the ignition OFF, press and hold the Valet/Program switch.

Turn the ignition ON and then back OFF while holding the Valet/Pro-

gram switch.
Release the Valet/Program switch.

Press and release the Valet/Program switch. The LED ﬂashes to report

the last shutdown for one minute or until the ignition is turned on, as
shown in the following table:

LED Flashes

Shutdown Mode

1 ﬂash

Runtime expired

2 ﬂashes

Over-rev shutdown

3 ﬂashes

Low or no RPM

4 ﬂashes

Transmitter shutdown (or optional push button)

5 ﬂashes

(+) Brake shutdown

6 ﬂashes

(-) Hood shutdown

Содержание Responder LC Model 991
































































Результаты поиска

Содержание Responder LC Model 991

Отзывы:

Похожие инструкции для Responder LC Model 991

Бренды по названию

Популярные бренды

Python Responder LC Model 991, Руководство по установке

Результаты поиска

Содержание Responder LC Model 991

Отзывы:

Похожие инструкции для Responder LC Model 991

Бренды по названию

Популярные бренды