EZ Plate™ Storage Water Heater
5
PV500-64 12/14
3
WATER HEATER INSTALLATION
3.1 Warranty
Factory warranty does not cover improper installation or operation. (See warranty for complete details).
Warranty exclusions include but are not limited to failure or malfunctions resulting from:
1. Failures to properly apply, install, operate, or maintain the appliance in accordance with printed instructions.
2. Abuse, alteration, accident, fire, flood and the like.
3. Sediment or lime buildup, freezing or any other conductions causing inadequate circulation.
4. Corrosive or contaminated atmosphere.
3.1 Checking Equipment Before You Install
Inspect the unit completely upon receipt from the freight carrier before signing the bill of lading. Inspect the appliance
and all accompanying parts for signs of impact or mishandling. Verify the total number of pieces shown on packing
slips with those actually received. Contact the freight carrier immediately if any damage or shortage is detected.
3.2 Codes
The equipment must be installed in accordance with the instructions in this manual, appliance markings and
supplemental instructions and in compliance with those installation regulations in force in the local area where the
installation is to be made. These must be carefully followed in all cases. Authorities having jurisdiction must be
consulted before installation is made. In the absence of such regulations, the installation must be in accordance with
the instructions in this manual, appliance markings, supplemental instructions and in compliance with the latest
edition of the applicable state and local mechanical and plumbing codes. The storage tank conforms to the current
edition of the ASME Boiler and Pressure Vessel Code Section IV, Part HLW and the plate heat exchanger conforms
to the current edition of the ASME Boiler and Pressure Vessel Code Section VIII.
3.3 Electrical
Requirements
This appliance is wired for 120VAC/1ph/60Hz service, as standard (check decal on product). The appliance must be
electrically grounded in accordance with the requirements of the authority having jurisdiction or in the absence of
such requirements, with the latest edition of the National Electrical Code ANSI/NFPA No. 70. When the unit is
installed in Canada, it must conform to the CAE C22.1, Canadian Electrical Code and/or Local Electrical Codes.
•
Supply the electrical service specified on the water heater data decal to each water heater. Separate electrical
circuits are recommended for multiple appliance installations.
•
Branch circuit protection and a disconnecting means must be furnished by the installer. Refer to the provided
wiring diagram when installing or troubleshooting electrical components of this appliance.
•
All wiring between the water heater and field installed devices must be made with type T copper wire of proper
size for the appliance load. Damage resulting from use of aluminum wiring is not covered by the product warranty.
•
Line voltage wire exterior to the water heater must be enclosed in approved conduit or approved metal clad cable.
•
Protect all water heater internal and external electrical components, wiring and electrical service connections from
water (dripping, spraying, rain, etc.) at all times.
Utiliser du fil de cuivre de la taille appropriée pour le service électrique entrant. Les dommages résultant de
l'utilisation de fil d'aluminium seront exclus du champ d'application de la garantie de cet appareil.
3.4 Handling and Locating the Water Heater
WARNING: Use industry standard safe rigging methods, such as including the use straps and spreader bars
and lifting from the water heater base skid assembly, when attempting to lift or move this product. Failure to
follow industry standard safe rigging methods can cause uncontrolled tipping or dropping the water heater,
resulting in property damage, personal injury or death.
1. Do not attempt to move or lift the water heater by the plumbing connections or heat exchanger. Lift only by the
skid using industry standard safe rigging methods.
2. Locate the water heater in a clean and dry area as close as possible to the greatest hot water usage and as near
to boiler water and/or electrical power as practical.
3. Confirm that the system utilities are adequate to meet the water heater requirements on the information decal.
