PVI Industries EZ Plate Скачать руководство пользователя страница 13

Страница: 13 / 24

EZ Plate™ Storage Water Heater

PV500-64 12/14

LED Display Alarm Messages

Alarm messages are displayed in the upper LED readout and alternate with the default display. An alarm LED ICON
is also illuminated.

ALARM

MESSAGE

CAUSE

RESULTS OF ALARM CONDITION

RECOMMENDED

ACTION

“P1”

TP1 probe failure

Inlet temperature sensor is not connected or is
reading incorrectly. Call for heat and burner
modulation output signal will revert to low fire.

Check wiring and sensor
Terminals 14 & 17

“P2”

TP2 probe failure

Temperature sensor is not connected or is reading
incorrectly.

Check wiring and sensor
Terminals 15 & 17

“P3”

TP3 probe failure

Temperature sensor is not connected or is reading
incorrectly or flue gas temperature protection is
disabled.

Check wiring and sensor
Terminals 16 & 17

“HA”

High temperature limit setpoint
exceeded

Audible alarm sounds, operation continues.

Press any button to reset

(while alarming)

“LA”

Low temperature alarm

Audible alarm sounds, operation continues.

AL1

Digital input 1 is activated.

Unit de-energized after timer delay. Audible alarm
sounds.

Press any button to reset

(while alarming)

AL2

Digital input 2 is activated.
This alarm indication is dedicated to
the Alarm On Any Failure feature of
this product.

Unit de-energized after timer delay. Audible alarm
sounds. Alarm contacts close for remote indication
of alarm. Internal alarm register will communicate
an alarm condition though the Modbus RTU
communication link.

Press any button to reset

(while alarming)

AL3

Digital input 3 is activated.

Unit de-energized after timer delay. Audible alarm
sounds.

Press any button to reset

(while alarming)

Mn1

Maintenance alarm for output 1

Buzzer sounds, operation continues

Check wiring and sensor

Mn2

Maintenance alarm for output 2

Buzzer sounds, operation continues

Check wiring and sensor

Mn3

Maintenance alarm for output 3

Buzzer sounds, operation continues

Check wiring and sensor

“rtc”

The real time clock has lost its
setting

Energy saving function disabled

Reprogram clock

CONTROL

MESSAGE

CAUSE

RESULTS OF CONTROL CONDITION

NOTES

A call-for-heat condition

The burner operating sequence should begin.

If the burner does not operate,
check safety devices or
Remote Proving Interlock

Flashing

The remote enable/disable has
been triggered

The small flame icon will flash indicating the
standby state

The

R1-R2

terminals have

been opened by the remote
master control. The heater will
remain in standby.

Integral circulation pump

The integral circulation pump will operate until the
water temperature has equalized

Pump may operate before,
during or after the call-for-heat

Содержание EZ Plate

























Результаты поиска

Содержание EZ Plate

Отзывы:

Бренды по названию

Популярные бренды

PVI Industries EZ Plate, Инструкция по установке и обслуживанию

Результаты поиска

Содержание EZ Plate

Отзывы:

Бренды по названию

Популярные бренды