manualshive.com logo in svg

PVI Industries EZ Plate, Инструкция по установке и обслуживанию

Поделиться
Скачать
PVI Industries EZ Plate Скачать руководство пользователя страница 11

EZ Plate™ Storage Water Heater 

 

 11 

PV500-64 12/14

 

The water heater operates to satisfy the set point of the TempTrac digital control whose sensor is located in a 
storage tank fitting. Demand (flow) will typically create a drop in temperature, thus activating the water heater to add 
heat to the stored water. This set point is the desired water temperature to maintain. 

 

 

 
Upper LED Readout 

The default display of the upper readout (Probe 1) is the water temperature near the hot water outlet. This sensing 
location serves as the primary control temperature for the TempTrac.  
This readout can display additional information by pushing the EXT button to cycle through the following items:  

•

  The temperature difference between Probe 1 and Probe 2. 

•

 All of the display information described above is available for monitoring through the optional MODBUS RTU 

interface. 

 

Lower LED Readout 

The default display of the lower readout (Probe 2) is the water temperature sensed near the middle of the water 
heater tank. This is used to anticipate changes in the stored water temperature and ensure a consistent water supply 
temperature. 

 

Control Buttons

 

SET 

Displays and modifies the temperature set points. 
In programming mode, it selects a parameter or confirms an operation. 

UP 

Displays and modifies the energy saving (Night Time setback) settings.  
In programming mode, it browses the parameter codes or increases a displayed value. 

DOWN 

Displays the working hours of the load relays. 
In programming mode, it browses the parameter codes or decreases a displayed value. 

CLOCK 

Changes lower display from the stored water temperature to current time and day. 

EXT 

Changes upper display from Probe 1 temperature to Probe 3 temperature, displays the 
temperature difference of the stored water temperature minus Probe 2 temperature and firing rate 
of the burner from 0 to 100%. In programming mode it sets the 4-20mA output (password is 
required). 

ON/OFF 

Switches the control ON or OFF. 

See TempTrac User Manual PV500-40, TempTrac Service and Setup Manual

 

PV500-41 and TempTrac BAS 

Connection and Protocol Information Manual PV 500-42 for additional TempTrac information. 

 

 

Содержание EZ Plate

























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды