manualshive.com logo in svg

Puxing PX-568, Руководство пользователя, Страница: 3 / 21

Поделиться
Скачать
Puxing PX-568 Скачать руководство пользователя страница 3

If the transceiver indicator displays

,it means the battery pack is out of 

power, please charge it.

 

Please always use the original charger. The charger’s indicator shows the 
charging status below.   
 

   
 
 
 
 

Please charge the battery pack as follow, 

1. Put the DC plug of the transformer into the DC socket of the charger unit. 

2. Connected the supplied transformer to the AC jack 
3. Slide the battery or the transceiver with a battery pack into the charger. 

4. Make sure the battery pack contacts are in contact with the charging 

terminals, and the charger LED is on, it begins to charge. 

5. After charging the supplied battery pack for 4 hours, remove it or the 

transceiver equipped with it from the charger. The charger light turns to 
green automatically after charging is completed. 

 

CAUTION 

1.  It is abnormal in case of the charger glisteningly before sliding the battery 

pack into the charger. 

2.  Don’t replace the battery pack until the indicator light is stable. 
3.  Make sure contact well, LED indicates red when it is charging, if LED 

always blinking the battery pack is damaged or over the environment 
temperature. 

 

MAINTENANCE 

1.  Don’t carry the radio by the antenna or microphone directly. 
2.  Use a soft, clean, dry cloth to clean the radio. 
3.  Please cover the speaker/microphone jacks with the supplied cover when 

the radio is not in used. 

4.  The keypad, knobs and case will become dirty after long use; you can use 

the soft detergent and cloth to clean it. 

 

INSTALLING ACCESSORIES AND OPTIONAL 

INSTALL /REMOVE BATTERY   
The average us time of the battery pack is 10 hours. 
It calculated as 5%TX time,5% RX time and 90% standby time. 

CAUTION 

Don’t short circuit the battery charger contacts or threw the battery into fire. 
Don’t disassemble the case of the battery. 

INDICATOR DISPLAY 

             

  STATUS 

RED CHARGING 

GREEN COMPLETED 

Содержание PX-568






















Отзывы:

Нет отзывов