background image

23 

Copyright © Puretec Pty Ltd 2022

NTS/NTX User Guide

Maintainance

Maintenance

1.  Isolate water supply by closing the inlet valve. 
2.  Relieve pressure by opening a tap down stream. Remove fill-port cap with the 

spanner provided. Some water will weep out of the head, however this is normal.

3.  Top-up the media as required, ensuring that you do not exceed the maximum level 

on the tank (more than 2/3 full).

4.  Replace fill-port cap onto the head and tighten with the spanner provided. Open 

the inlet valve, the system is now ready for use.

Media Replacement

The NTS neutraliser sytems use a pure calcium carbonate media. The NTX neutraliser 
sytems use a pure calcium carbonate & magnesium oxide media. During water usage a 
specific amount of media is consumed, thus requiring periodic top-ups for a continuous 
supply of treated water. The frequency is dependent on the pH level and water usage. 
Always replenish the media before the supply is exhausted. No extra water is required when 
topping up the media level.

An easy way to determine if the neutraliser requires media replenishment is to place a mark 
on the outside of the unit at the maximum level of the media when first installed. Every 2-3 
months check the level by shining a light through the tank and compare the current level 
to the maximum. If you are unable to see through the tank, remove the fill-port cap and 
measure down to the top of the media. Add more media if the media is more than 2 inches 
below the mark. See individual Model Information pages for media codes and filling order.

The media storage capacity is as per the following, and should be no more than 2/3 full.

Model

Capacity – x Litres

Maximum Flow – x Litres *

NTS1000 

15

40

NTS2000 / NTX2000

30

70

NTS3000 / NTX3000

45

90

NTS4000 / NTX4000

60

100

NTS70-C / NTX70-C

70

120

NTS120-C / NTX120-C

100

150

* The lower the pH (acidity) of the water being treated, the greater the attrition rate of the 
media and the slower the water should pass through the bed. The unit should be sized 
according to the level of pH and existing flow rate.

Содержание NTS Series





























Отзывы: