PUMPIRAN PB3 Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 39

background image

PB3 User Instruction

Page 15 of 39

The design of foundation is not the responsibility of PUMPIRAN. It is therefore recommended that the
customer consult a competent specialist skilled in the field of foundations, to insure proper design/installation of
the foundation.

3.2.1 Installation check list

a)

Level Base plate.

b)

Preliminary Alignment.

c)

Grout Base plate - Check Foundation Bolts

d)

Alignment Shaft/Coupling.

e)

Piping installed – correct vent, gauge, valve, suction strainer and pipe support locations?

f)

Check Coupling Alignment.

g)

Coupling guard correctly installed?

3.2.2 Level the baseplate

Before putting the unit on the foundation, thoroughly clean the top of the foundation. Break off any loose pieces
of cement and roughen the top with a chisel to afford a good hold for grout.

NOTE

When lifting base plate with pump, sling base plate from all lifting eyes provided.
Failure to do this may result in permanent deformation of base plate.

NOTE

Pump, driver auxiliary equipment and piping shall be removed from the base plate
before leveling the baseplate.

Locate the base plate in its proper position on the concrete block together with the leveling screws as shown in
the General Arrangement Drawing.

Using a precision level across the machined surfaces of the pump and driver mounting pads, adjust leveling
screws as necessary to ensure that base plate is leveled in all directions.

When the base plate is leveled, snug the foundation bolts, but do not completely tighten.

Using the previous procedure, adjust base plate until pump and driver are within 0.1 mm .

3.3 Grouting

The following ASTM Specifications are furnished as references for test methods used in conjunction with
installation of grouting materials and should be used to obtain proper results:

-

ASTM C 78-84, Test Method for Flexural Strength for Concrete

-

ASTM C 109-90, Test Method for Compressive Strength of Hydraulic Cement Mortars – Modified

-

ASTM C 469-87a, Test Method for Static Modulus of Elasticity and Poisson’s Ratio of Concrete in

Compression

-

ASTM C 496-90, Test Method for Splitting Tensile Strength of Cylindrical Concrete Specimens

-

ASTM C 531-85, Test Method for Linear Shrinkage and Coefficient of Thermal Expansion of Chemical

Resistant Grouts and Monolithic Surfacing – Modified

-

ASTM C 666-90, Test Method for Resistance of Concrete to Rapid Freezing and Thawing

-

ASTM C 939-87, Test Method for Flow of Grout for Preplaced Aggregate Concrete (Flow Cone Method)

«
...
13
14
15
16
17
...
»

Содержание PB3








































Отзывы:

Нет отзывов

Похожие инструкции для PB3

Бренд: TapFlo Страницы: 31

Бренд: vacuubrand Страницы: 44

Бренд: Parker Страницы: 12

Бренд: Walrus Страницы: 12

ROYTRONIC A Series

Бренд: LMI Страницы: 36

Бренд: American Plumber Страницы: 2

Aeromax Piscine 10

Бренд: Thermor Страницы: 32

Бренд: Bard Страницы: 27

TV 301 Navigator 969-8918

Бренд: Varian Страницы: 55

Бренд: Ecoplus Страницы: 24

Бренд: ThermoFlow Страницы: 34

Бренд: Zenit Страницы: 24

Бренд: Bradford White Страницы: 21

Zoneline AZ91H18E E Series

Бренд: GE Страницы: 78

Бренд: Waterous Страницы: 7

Бренд: CleanCraft Страницы: 22

Бренд: Ozito Страницы: 6

Бренд: VARISCO Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды