PTI PX 300 Скачать руководство пользователя страница 22 | Manualshive

Страница: 22 / 35

PTI PX 300 Скачать руководство пользователя страница 22

Page 22

Sponson Sheeting

Sponson Top

Build the Sponsons Con’t

Ride Pads

Sponson Tops

A:

Prepare the top of each sponson. Using a sanding block, sand diagonally length wise up and down the sponson

until the keelson is flush (and a slight angle) with the former AND the Non trip is flush with the outside sponson as
shown

B:

Locate the “Sponson Tops” from

SHEETING SHEET 2

C:

We suggest adding flotation to the sponsons increase the hull is breached. Using Styrofoam, Pool Noodles or in-

sulation foam. Cut to shape to fit the sponson bay as shown

D:

Test Fit a Sponson top, make sure it covers the sponson leaving some overhang all around

E:

Begin by brushing the underside of the sheet with resin to seal it, WHILE ITS WET place on top of the sponson

(wet side down) BE SURE it covers the sponson and TAPE IT with masking tape!!
BE SURE TO USE LOTS we can not have the sheeting separate from the sponson
Then clamp it to a flat surface, either place it on 1/8” squares or over the edge so the top sheet does not interferer

Note Overhang

A

A

«
...
20
21
22
23
24
...
»

Содержание PX 300




































Отзывы:

Нет отзывов