PTI PX 300 Скачать руководство пользователя страница 2 | Manualshive

Страница: 2 / 35

PTI PX 300 Скачать руководство пользователя страница 2

`Getting Started

Before you get started you will need:
A flat building surface, we recommend piece of wood 1/2” to 3/4” thick. About 12” wide and 36” long.
We also recommend covering the side you will build on with wax paper to prevent the parts sticking to the
building board

Things to know before you start

Please review the parts list located at the back of this manual. Become familiar with the sheet name and the parts located on them
Your PTI boat kits was cut with a Laser Cutter specifically designed for plywood. Small tabs are left to hold the pieces while they are being
cut. To remove the piece press gently near the tab and the part should push out. HOWEVER if it does no come out easily we recommend
cutting the tab with a hobby knife as shown below

Page

2

Introduction

Tools required

Hobby Knife

Hobby Saw

Various C Clamps or Spring clamps

Masking Tape
Super Glue (CA) we recommend the “Thick” formula
Sanding Block

Sand Paper

30 Minute Epoxy Glue

Epoxy Resin

Small paint brushes

Optional:

Stanley “Sure Form”

PLEASE NOTE

: All these items are available on our web site, please see

our online store

TAB

«
1
2
3
4
...
»

Содержание PX 300




































Отзывы:

Нет отзывов