background image

WIL-19011-E-07

 

WILDEN PUMP & ENGINEERING, LLC

S e c t i o n   6

S U G G E S T E D   I N S T A L L A T I O N

The model XSD1 has a 25 mm (1") inlet/discharge. The model 
XSD2 has a 51 mm (2") inlet/discharge and the XSD3 has a  
76 mm (3") inlet/discharge. The Equalizer

®

 can be installed 

in either horizontal or vertical orientations. A variety of 
materials are available to satisfy temperature, chemical 
compatibility, abrasion and flex concerns. 
The Equalizer

®

 installed on the discharge side of the pump 

minimizes pulsation and protects in-line equipment. It can 
also be connected on the suction side to prevent water 
hammer associated with a positive inlet condition.
Install the Equalizer

®

 as shown below. The use of flexible 

connections and a Filter, Regulator, Lubricator (FRL) will 
extend parts life. Shut-off valves on the suction side of 

pump and the discharge side of Equalizer

®

 will enable 

maintenance personnel to safely service the equipment. 
To maximize effectiveness, install the Equalizer

®

 as close 

as possible to the discharge of the pump.
It is important to support the pipe immediately 
downstream from the Equalizer

®

. Use a tee connector 

on the pump air supply line and connect the line to the 
Equalizer

®

 regulator body. This tee connector should be 

installed after the FRL. The Equalizer

®

 consumes very 

little air, therefore, a 1/4” hose is more than adequate to 
supply enough air volume. When the air supply to the 
pump is shut down, the air to the Equalizer

®

 will be shut  

off as well.

NOTE: In the event of a power failure, the shut-off 
valve should be closed if the restarting of the pump is 
not desirable once power is regained.

AIR-OPERATED PUMPS: To stop the pump from 
operating in an emergency situation, simply close 

the shut-off valve (user supplied) installed in the air 
supply line. A properly functioning valve will stop the 
air supply to the pump, therefore stopping output. This 
shut-off valve should be located far enough away from 
the pumping equipment such that it can be reached 
safely in an emergency situation.

SUCTION LINE

DISCHARGE LINE

SHUT-OFF VALVE

FLEXIBLE CONNECTION

FLEXIBLE CONNECTION

AIR SUPPLY

SHUT-OFF VALVE

SHUT-OFF VALVE

PRESSURE GAUGE

AIR SHUT-OFF VALVE

COMBINATION FILTER AND REGULATOR

NEEDLE VALVE

AIR INLET

SHUT-OFF VALVE

PRESSURE GAUGE

Содержание Wilden XSD Series





























Отзывы: