ProMinent Sigma/ 2 Control S2Cb Скачать руководство пользователя страница 26

Страница: 26 / 100

Installation

CAUTION!
Danger of injury to personnel and material damage
The disregard of technical data during installation may

lead to personal injuries or damage to property.
–

Observe the technical data- refer to chapter "Tech‐

nical Data" and, where applicable, the operating

instructions of the accessories.

7.1 Installation, hydraulic

WARNING!
Danger of fire with flammable feed chemicals
–

Only metering pumps with the identity code option

"Multi-layer safety diaphragm with rupture signalling

with electrical signal" are permitted to meter flam‐

mable media, with back pressures over 2 bar and if

the operator takes appropriate safety precautions.

WARNING!
Warning of feed chemical reactions to water
Feed chemicals that should not come into contact with

water may react to residual water in the liquid end that

may originate from works testing.
–

Blow the liquid end dry with compressed air through

the suction connector.

–

Then flush the liquid end with a suitable medium

through the suction connector.

WARNING!
The following measures are an advantage when working

with highly aggressive or hazardous feed chemicals:
–

Install a bleed valve with recirculation in the storage

tank.

–

Install an additional shut-off valve on the discharge

or suction ends.

CAUTION!
Warning of feed chemical spraying around
PTFE seals, which have already been used / com‐

pressed, can no longer reliably seal a hydraulic connec‐

tion.
–

New, unused PTFE seals must always be used.

CAUTION!
Suction problems are possible
The valves may no longer close properly with feed

chemicals with a particle size of greater than 0.3 mm.
–

Install a suitable filter in the suction line.

Installation

Содержание Sigma/ 2 Control S2Cb





































































































Результаты поиска

Содержание Sigma/ 2 Control S2Cb

Отзывы:

Бренды по названию

Популярные бренды

ProMinent Sigma/ 2 Control S2Cb, Руководство по эксплуатации

Результаты поиска

Содержание Sigma/ 2 Control S2Cb

Отзывы:

Бренды по названию

Популярные бренды