ProMinent Sigma/ 2 Control S2Cb Скачать руководство пользователя страница 10

Страница: 10 / 100

WARNING!
Warning of hazardous feed chemical
Should a dangerous feed chemical be used: it may

escape from the hydraulic components when working on

the pump, material failure or incorrect handling of the

pump.
–

Take appropriate protective measures before

working on the pump (e.g. safety glasses, safety

gloves, ...). Adhere to the material safety data sheet

for the feed chemical.

–

Drain and flush the liquid end before working on the

pump.

WARNING!
Danger from hazardous substances!
Possible consequence: Fatal or very serious injuries.
Please ensure when handling hazardous substances

that you have read the latest safety data sheets provided

by the manufacture of the hazardous substance. The

actions required are described in the safety data sheet.

Check the safety data sheet regularly and replace, if

necessary, as the hazard potential of a substance can

be re-evaluated at any time based on new findings.
The system operator is responsible for ensuring that

these safety data sheets are available and that they are

kept up to date, as well as for producing an associated

hazard assessment for the workstations affected.

CAUTION!
Warning of feed chemical spraying around
Feed chemical can spray out of the hydraulic compo‐

nents if they are manipulated or opened due to pressure

in the liquid end and adjacent parts of the system.
–

Disconnect the pump from the mains power supply

and ensure that it cannot be switched on again by

unauthorised persons.

–

Depressurise the system before commencing any

work on hydraulic parts.

CAUTION!
Warning of feed chemical spraying around
An unsuitable feed chemical can damage the parts of

the pump that come into contact with the chemical.
–

Take into account the resistance of the wetted mate‐

rials and the

[ERROR: Missing definition for variable

"Hersteller"!]

Resistance List when selecting the

feed chemical - see the

[ERROR: Missing definition

for variable "Hersteller"!]

Product Catalogue or visit

[ERROR: Missing definition for variable "Hers‐

teller"!]

Safety information

Safety Chapter

Содержание Sigma/ 2 Control S2Cb





































































































Результаты поиска

Содержание Sigma/ 2 Control S2Cb

Отзывы:

Бренды по названию

Популярные бренды

ProMinent Sigma/ 2 Control S2Cb, Руководство по эксплуатации

Результаты поиска

Содержание Sigma/ 2 Control S2Cb

Отзывы:

Бренды по названию

Популярные бренды