manualshive.com logo in svg

Proliphix Professional NT100e/h, Руководство по настройке, Страница: 80 / 100

Поделиться
Скачать
Proliphix Professional NT100e/h Скачать руководство пользователя страница 80

Beta Draft Confidential

3-44

Professional Series Network Thermostat Configuration Guide, Release 3.0

Part No. 600-01000-200, Rev. 2

CHAPTER  3: Configuring the Thermostat Using the TMI

Threshold
(NT150e/h and NT160e/h only)

Depending on the action selected by the 

External Relay Trigger 

(NT150e/h and NT160e/h only) (page 3-43)

, this setting 

represents the limits of either temperature or relative humidity as 
required by the External Relay Trigger action above. This setting 
is measured in either % relative humidity or degrees 
Fahrenheit/Celsius.

„

10% to 90% RH

 – For Above humidity limits. When the 

relative humidity rises above this trigger point, the external 
relay is activated. When the relative humidity falls 5% below 
the trigger point, the relay is deactivated.

„

10% to 90% RH

 – For Below humidity limits. When the 

relative humidity falls below the trigger point, the external 
relay is activated. When the relative humidity rises 5% 
above the trigger point, the relay is deactivated.

„

-30

°

F(-34

°

C) to 200

°

F(95

°

C)

 – For Above temperature 

limits. When the average temperature rises above this trigger 
point, the External Relay is activated. When the temperature 
falls below trigger setpoint minus the setpoint differential, 
the relay is deactivated.

„

-30

°

F(-34

°

C) to 200

°

F(95

°

C)

 – For Below temperature 

limits. When the average temperature falls below the trigger 
point, the External Relay is activated. When the temperature 
rises above the trigger setpoint plus the setpoint differential, 
the relay is deactivated. 

Activate Polarity
(NT150e/h and NT160e/h only)

Select Open or Closed for the active state of the External Relay. 
For example, when the relay is set to a polarity of 

Closed

, the 

relay closes and completes the external circuit when activated.

„

Open

 – Contacts are open and the external circuit is 

unswitched.

„

Closed

 – Contacts are closed and the external circuit is 

completed.

Activate HVAC Fan
(NT150e/h and NT160e/h only)

Select 

Enable

 to activate the HVAC fan when the External Relay 

is activated. The HVAC fan turns off when the External Relay is 
deactivated. This feature is best applied when humidification or 
de/humidification is performed by additional equipment outside 
the HVAC system but the same duct work is used. 

„

Enable

 – Allow airflow in the duct work during External 

Relay activation.

„

Disable

 – Disallow airflow in the duct work during External 

Relay activation.

Table 3-6 Advanced Settings Fields - HVAC Fuel Burner Field Descriptions 

Field

Description

Содержание Professional NT100e/h





































































































Отзывы:

Нет отзывов