Proliphix Professional NT100e/h Скачать руководство пользователя страница 73 | Manualshive

Страница: 73 / 100

Proliphix Professional NT100e/h Скачать руководство пользователя страница 73

Beta Draft Confidential

Advanced Settings Page

Professional Series Network Thermostat Configuration Guide, Release 3.0

3-37

Part No. 600-01000-200, Rev. 2

Use

Table 3-6

to configure the

Advanced Settings

for a parameters.

Table 3-6 Advanced Settings Fields - HVAC Fuel Burner Field Descriptions

Field

Description

HVAC System Type

Select the type of HVAC system, either

Fuel Burner

(default)

or

Heat Pump

HVAC systems as follows:

Fuel Burner

(default) – The HVAC system burns fossil

fuels (e.g. gas or oil). Typically the system includes either an
oil or gas fired boiler or furnace. See

Figure 3-15 on

page 3-36

and continue with

If Your HVAC System is a Fuel

Burner (page 3-37)

.

Heat Pump

– Specifies that the HVAC system is based on

an electric compressor. See

Figure 3-14 on page 3-35

and

continue with

If Your HVAC System is a Heat Pump (page

3-38)

.

Note: When selecting between either

Fuel Burner

or

Heat

Pump

or

between Heat Pump

and

Fuel Burner

, the HVAC

Mode must be set to Off prior to selecting the opposite setting.
See the

Status & Control Page (page 3-9)

.

If Your HVAC System is a Fuel Burner

Heat Control

Select the HVAC control for this thermostat. This parameter
describes the thermostat capability to control a single stage or
dual stage heating system. The thermostat can also be disabled
from controlling a heating system and instead operate as a
cool-only thermostat. (See

Cool Control (page 3-38)

.)

Disable

– No heating system exists. (A/C only thermostat.)

1H

– Enables the heating system as a standard single stage

system.

2H

(default) – Enables the heating system as a dual stage

system.

2

nd

Stage Offset

Specify the second stage heat set point temperature referenced to
the first stage heat set point temperature. This parameter is only
enabled when

2H

Heat Control

is selected, otherwise it is

disabled. (e.g. If the first stage temperature set point is set to
70°F, and this parameter were set to -3°F, the second stage heat
would activate at or below 67°F). Temperatures include:

0, -2, -3, -4, -5, -6 °F (0, -1.0, -1.5, -2.0, -2.5, -3.0 °C)

– Second

stage heat temperature offset from first stage heat set point
temperature.

«
...
71
72
73
74
75
...
»

Содержание Professional NT100e/h





































































































Отзывы:

Нет отзывов