Proliphix Professional NT100e/h Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 100

Proliphix Professional NT100e/h Скачать руководство пользователя страница 70

Beta Draft Confidential

3-34

Professional Series Network Thermostat Configuration Guide, Release 3.0

Part No. 600-01000-200, Rev. 2

CHAPTER 3: Configuring the Thermostat Using the TMI

Port

Enter the Syslog server IP port, which allows you to use a
custom program to receive alarm/alert notifications.

wxyz

– Four digit (max) standard IP port number designation.

The default port number is

514

.

Repeat Interval

Select the Syslog messaging periodic interval. This is the rate at
which Syslog messages are emitted from the thermostat.

1, 5, 30, 60

–The amount of time in minutes between successive

Syslog messages sent by the thermostat after an error event and
before the error event is cleared.

Syslog alarm/alert messages are sent to the Syslog server every
minute until the alarm/alert condition is cleared on the
thermostat. Alarm/alert messages are sent with a

Local7 Facility

Code

and with a severity level of

Alert

as defined in RFC 3164.

In addition to alarms and alerts, the System Start event
(generated during thermostat start up) is also reported to the
Syslog server. These events are not repetitive but only occur
once when the event occurs.

Table 3-5 Network Settings Field Descriptions (Continued)

Field

Description

«
...
68
69
70
71
72
...
»

Содержание Professional NT100e/h





































































































Отзывы:

Нет отзывов