manualshive.com logo in svg

Proliphix Professional NT100e/h, Руководство по настройке, Страница: 78 / 100

Поделиться
Скачать
Proliphix Professional NT100e/h Скачать руководство пользователя страница 78

Beta Draft Confidential

3-42

Professional Series Network Thermostat Configuration Guide, Release 3.0

Part No. 600-01000-200, Rev. 2

CHAPTER  3: Configuring the Thermostat Using the TMI

A/C Humidity Control 
(NT150e/h and NT160e/h only)

Select a relative humidity value from 10% to 90%. When the 
measured RH rises above a preset threshold, the HVAC cooling 
cycle is initiated. The cycle continues until the humidity level 
falls 5% below the trigger level or until a heat setpoint is 
encountered. When a heat setpoint is encountered, the HVAC 
heating cycle is invoked. After the heat setpoint has been 
satisfied, the HVAC cooling cycle (to satisfy humidity 
requirements) is delayed for 5 minutes. Humidity control is 
intended for moderate moisture control. High humidity 
environments should also include secondary dehumidification 
equipment. 

„

Disable

 – This feature is disabled and the A/C system may 

not be used to reduce humidity.

„

10% – 90%

 – Humidity threshold expressed in 5% 

increments.

Table 3-6 Advanced Settings Fields - HVAC Fuel Burner Field Descriptions 

Field

Description

Содержание Professional NT100e/h





































































































Отзывы:

Нет отзывов