background image

REHATEAM s.r.l.—vicolo Negrelli 

5

31040 

Castagnole di Paese TV  

-

 www.rehateamprogeo.com

 

Service Manual CARBOMAX    7

 

 

 

SERVICE MANUAL 

DIRECTIONALITY

 

A very important aspect of any wheelchair is its directionality. 

To check if the wheelchair goes straight, sit on it, push it and let it go until it stops. 

If something is wrong, the slower the wheelchairs moves forward (momentum close to nothing), the more likely it turns right or left. There-
fore, if no or irrelevant turn occurs, the wheelchair is properly adjusted. 

Cause

 

Reason 

 

Solution

 

SURFACE 

The surface where the test is being performed is not even 
and flat 

Test the chair on even and flat surface 

REAR WHEELS 

 

The rear wheel are not equally inflated 

Inflate both tyres at the same pressure 

The tyres of the two rear wheel are different or differently 

Change the tyres 

The rear wheels are not adjusted at the same height 

Adjust the rear wheel height 

The camber of right and left wheels are different or differ-
ently adjusted 

Adjust the camber. 

  

The wheel, when turning, touches the side guard or the 
brakes 

Fix or replace the side guard. Add spacer on the 
receiver. Adjust the brake. 

The wheels doe not turn smoothly 

Clean or change the bearings 

FRONT WHEELS  The casters are not adjusted at the same height 

Adjust the front wheels at the same height 

The tyres of the two front wheels are different or differently 

Change the wheels 

The fixing bolts of the fork/fork support/clamp are loosened 

Check and tighten all fixing bolts 

The caster does not turn smoothly 

Clean the bearings. 

Either or both forks are not adjusted so as their axis is per-
pendicular to the ground. 

Adjust the fork axis inclination. 

  

FOOTPLATE 

The  footplate tubes are adjusted at different height.  

Adjust the tubes at the same height 

If the wheelchairs does not go straight, in most cases the reason 
is the fork angle adjustment. 

However, before working on the fork angle adjustment, check all 
the points above mentioned. 

First, make the test along a flat even surface to check the direc-
tionality. 

The  correct  adjustment  has  both  forks  perpendicular  to  the 

ground, that is, their axis at 90°.

 

If the wheelchair 

TURN RIGHT,

 the cause is one or more of 

the following: 
The 

RIGHT

 fork is tilted 

inwardly 

and/or 

backward 

 

The 

LEFT

 fork is tilted 

outwardly

 and/or f

rontward  

3

 If the wheelchair 

TURN LEFTT,

 the cause is one or more of 

the following: 
The 

LEFT

 fork is tilted 

inwardly 

and/or 

backward 

 

The 

RIGHT

 fork is tilted 

outwardly

 and/or f

rontward  

90°               90°        

90°              90°        

1

 

 

 

2

 

 

 

 

3

 

Follows next page 

Содержание CARBOMAX






















Отзывы: