background image

REHATEAM s.r.l.—vicolo Negrelli 

5

31040 

Castagnole di Paese TV  

-

 www.rehateamprogeo.com

 

Service Manual CARBOMAX    2

 

 

 

SERVICE MANUAL 

CARBOMAX 

 

GENERAL WARNINGS 

ANY  ADJUSTMENT  CAN  BE  CARRIED  OUT  EXCLUSIVELY  BY  QUALIFIED 
AND AUTHORIZED BY REHATEAM® PERSONNEL. 

It is forbidden to carry out any modifications, even when possible, to the original 
design. 

Any  adjustments  and/or  any  modification  that  is  carried  out  by  non-authorized 
personnel  will  immediately  void  the  warranty  on  the  product  and  it  relieves      
RehaTEAM® from any responsibility on any malfunctioning and/or damage due 
to such adjustments/modifications. 

Always  contact  RehaTEAM®  and  its  technicians  for  any  non-standard             
requirements or modifications to allow them to evaluate such modifications and 
verify that they will not compromise the normal and safe use of the wheelchair. 

Any  modification  of  the  original  parameters  and  set  up  could  seriously            
compromise  the  safe  operation  of  the  wheelchair  causing  damage  to  both  the 
user and the wheelchair itself. 

 

After every adjustment made to the wheelchair, check carefully that all parts are 
correctly fixed. Check that all screws and nuts are tightened and that all moving 
parts are functioning correctly. 

After  any  adjustment,  always  test  the  wheelchair  before  giving  the  product  to    
user and/or his/her attendant

RehaTEAM® disclaims any responsibility for damage to the product or the peo-
ple due to any modification that is not properly performed or  that, in any case, 
does not guarantee safety to the user. 

Содержание CARBOMAX






















Отзывы: