ProGear Hendrickson HN 422FR Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 41

ProGear Hendrickson HN 422FR Скачать руководство пользователя страница 33

HN

®

FR Series

Component Replacement

32

17730-285

FIGURE

8-14

A   B A R   P I N   S H I M   M U S T   B E
I N S TA L L E D  AT   E A C H   B O LT
LOCATION. THE SAME PART
NUMBER SHIM IN THE SAME
ORIENTATION MUST BE USED
AT   B OT H   B O LT   LO CAT I O N S
ON ANY ONE END BUSHING.
DO NOT INSTALL OR STACK
M O R E  T H A N   O N E   S H I M  AT
EACH BOLT LOCATION. USE
G E N U I N E   H E N D R I C K S O N
BAR PIN SHIMS, DO NOT USE
STANDARD WASHERS. FAILURE
TO FOLLOW THESE WARNINGS
M AY   R E S U LT   I N   I M P R O P E R
VEHICLE ALIGNMENT, FRACTURE
OF THE AXLE BRACKET OR BAR PIN WHICH COULD RESULT IN THE LOSS OF VEHICLE CONTROL AND
POSSIBLE PERSONAL INJURY OR PROPERTY DAMAGE.

FIGURE

8-15

THE BAR PIN ALIGNMENT SHIM

(P/N 50130-000)

MUST BE INSTALLED WITH THE FOLDED EDGE
FACING AWAY FROM THE BUSHING, SEE FIGURE
8-15. FAILURE TO DO SO MAY RESULT IN SHIM
DAMAGE, IMPROPER ALIGNMENT, DAMAGE OR
FRACTURE OF THE AXLE BRACKET OR BAR PIN
WHICH COULD RESULT IN THE LOSS OF VEHICLE
CONTROL AND POSSIBLE PERSONAL INJURY OR
PROPERTY DAMAGE.

4. Partially install the

FRONT INBOARD

bar

pin alignment shim and verify that the shim is in the same orientation as prior to disas-
sembly, see Figure 8-13.

5. To complete installation of the alignment shim, remove the temporary ¾" bolt from the

inboard bar pin hole and complete installation of the inboard alignment shim.

6. Install the NEW 1" inboard bar pin fasteners.

DO NOT

tighten at this time.

7. Repeat Steps 4 through 6 for the

FRONT OUTBOARD

alignment shim.

8. Chock

the

REAR

drive axle wheels to prevent movement while installing the rear bar pin

into the axle bracket.

9. Support the current axle position of the rear axle pinion with a jack to assist with the instal-

lation of the rear bar pin.

NOTE

Prior to disassembly of the longitudinal torque rod, note the quantity and orientation of the
longitudinal torque rod shims. It is required that the longitudinal torque rod shims are installed in the
same orientation and location as removed to preserve the existing pinion angle.

10. Disconnect the longitudinal torque rod from the axle bracket, see vehicle manufacturer’s

specifications.

11. Release the rear parking brakes, this will allow the rear axle to rotate without rotating the

tires.

12. Lower the rear drive pinion until the rear drive axle bracket legs are parallel to the rear bar

pin flats, see Figure 8-16.

Rear
Axle Bracket

Equalizing Beam

Bar Pin

Lower Pinion

Part Number

50130-000

Part Number

50131-000

Part Number

57026-000

3 16

/ " Leg

1 8

/ " Leg

NOTE:

Folded edge in 50130-000 shim

must be positioned away from bushing

3 8

/ " Leg

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
31
32
33
34
35
...
»

Содержание Hendrickson HN 422FR










































Отзывы:

Нет отзывов