ProGear Hendrickson HN 422FR Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 41

ProGear Hendrickson HN 422FR Скачать руководство пользователя страница 29

HN

®

FR Series

Component Replacement

28

17730-285

VEE BRACKET

DISASSEMBLY

1. Chock the wheels.

SERVICE HINT

Access to the lower anchor plate assembly fasteners can be gained from the outboard side of
the equalizing beam.

2. Remove the lower anchor plate assembly from the inboard side of the equalizing beam.

Access to the fasteners can be gained from the outboard side of the equalizing beam.

3. Remove the lower bolster spring fasteners on the side being serviced (4 fasteners per

bolster).

4. Raise the frame enough to clear the Vee bracket from the equalizing beam aligning pins,

see Figure 8-7. Support the frame at this height with frame stands.

5. Remove the four (4) Vee bracket ¾" fasteners.

6. Remove the Vee bracket from the equalizing beam.

FIGURE 8-7

Equalizing Beam

Bolster Spring with
Vee Bracket Assembly

¾" Hex Head Bolt

¾" Vee Bracket Locknut

Tightening Torque 220-300 ft. lbs.

Equalizing Beam Aligning Pins

ASSEMBLY

1. Mount Vee bracket over aligning pins on equalizing beam, see Figure 8-7.

2. Install the four Vee bracket fasteners.

DO NOT

tighten at this time.

THE BOLSTER SPRING MOUNTING BOLT HEADS MUST BE POSITIONED AT THE RUBBER SIDE OF THE
BOLSTER SPRINGS TO PREVENT THE BOLSTER SPRINGS FROM BEING DAMAGED BY THE THREADED
ENDS OF THE BOLTS.

3. Lower the frame enough to align the four (4)

lower

bolster spring holes to the Vee bracket.

4. Loosely install the fasteners securing the bolsters to the saddle and the equalizing beam

assembly making sure the bolt heads are towards the bolster springs.

5. Completely lower the vehicle.

6. Tighten all bolster spring locknuts to

33-45 foot pounds torque, see Figure 8-8.

7. Tighten Vee bracket ¾" locknuts to

220-300 foot pounds torque, see Figure 8-8.

SERVICE HINT

Access to the lower anchor plate assembly fasteners can be gained from the outboard side of
the equalizing beam.

8. Install the lower anchor plate assembly through the rebound strap and attach it to the

equalizing beam. Tighten the fasteners to

90-105 foot pounds torque.

9. Remove the wheel chocks.

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
27
28
29
30
31
...
»

Содержание Hendrickson HN 422FR










































Отзывы:

Нет отзывов