ProGear Hendrickson HN 422FR Скачать руководство пользователя страница 23 | Manualshive

Страница: 23 / 41

ProGear Hendrickson HN 422FR Скачать руководство пользователя страница 23

HN

®

FR Series

Alignment & Adjustments

22

17730-285

AUXILIARY SPRING SHIM EVALUATION

The HN FR suspension uses a dual spring design to achieve a good empty ride while maintain-
ing a stable ride when loaded. When empty, the vehicle rides on the bolster springs and there
is an air gap between the auxiliary springs and the Vee bracket. When loaded, the weight of
the vehicle compresses the bolster springs until the auxiliary spring engages the Vee bracket,
thereby increasing roll stability. However, vehicles with a high unladen tandem weight or a high
center of gravity may require high roll stability at all times. On these vehicles, auxiliary spring
shims may be added until the auxiliary spring and the Vee bracket are engaged at all times. This
will eliminate any gap between the auxiliary springs and the Vee bracket. A maximum of five (5)
shims may be installed above each auxiliary spring.

NOTE

Both sides of the HN FR suspension must have an equal number of shims in place or a vehicle
lean may result.

Most production vehicles are manufactured with three (3) auxiliary spring shims above the
auxiliary spring, see Figure 7-6. However, some vehicles are manufactured with only one shim to
minimize the need for adjustment after the body equipment is installed.

To achieve optimal ride quality and stability the unladen tandem weight of a vehicle will dictate
the auxiliary spring shim arrangement necessary above the auxiliary spring, see chart below for
details.

TABLE 7-1

RECOMMENDED AUXILIARY SHIM CONFIGURATION

UNLADEN TANDEM WEIGHT WITH BODY / EQUIPMENT / EMPTY TRAILER INSTALLED

10,000–18,000 lbs.

18,001–28,000 lbs.

STD–3 Shims

2 Shims

FIGURE

7-6

DISASSEMBLY

1. Chock the wheels.

2. Loosen the nuts that attach the auxil-

iary spring assembly to the saddle.

3. Remove or install additional shims as

recommended.

ASSEMBLY

1. Re-assemble fasteners and tighten

locknuts to 90-105 foot pounds
torque.

2. Remove the wheel chocks.

Pro Gear and Transmission • 906 W. Gore St. Orlando, FL 32805 • 1 (877) 776-4600 / (407) 872-1901 • [email protected]

«
...
21
22
23
24
25
...
»

Содержание Hendrickson HN 422FR










































Отзывы:

Нет отзывов