10
Sharpen and maintain the chainsaw in accordance with
the manufacturer‘s instructions.
If the tool becomes jammed during cutting, it has to be
turned off immediately and freed carefully. Afterwards,
the machine has to be checked for damage (e.g. bent
chain bar) and a test run has to be carried out.
For felling or cross-cutting, the spike bar (claw stop)
must be applied to the wood to be cut. The use of the
spike bar is also recommended when cutting through
thick branches.
Before every cross-cut, firmly position the spike bar and
only then saw into the wood with the chainsaw running.
The saw is then lifted up using the rear grip and guided
using the front handle. The spike bar acts as a pivot
point. Repositioning is done using light pressure on the
front handle. Pull the saw back slightly to do this. Insert
the spike bar deeper and lift up again using the rear grip.
Use only admitted chain saw and chain bar
combination
The cutting equipment supplied is optimally matched to
this chain saw.
When pairing of components do not match, the cutting
attachment can be irreparably damaged after only a
short operating time and cause injury.
NOTE
The following information is mainly for the end user or
the infrequent user.
This chainsaw has been designed for occasional use by
home owners, garden owners and campers, for general
work such as clearing, cutting firewood etc. It is not
intended for longer work. During longer work, because
of vibrations, there is a risk of circulation problems in
the user‘s hands (white-finger-syndrome).
White-finger-syndrome (Raynaud’s Disease) is a
vascular disease where the small blood vessels in
fingers and toes contract seizure-like. The affected
areas are no longer supplied with blood and therefore
look very pale.
Frequent use of vibrating machines can cause nerve
damage in people whose circulation is compromised
(e.g. smokers, people with diabetes).
If you notice unusual impairment, immediately stop the
work and consult a doctor. Observe the following
notices in order to reduce risks:
•
Keep your body, and particularly your hands, warm in
cold weather.
•
Take regular breaks during which you should move
your hands to promote circulation.
•
Ensure the lowest possible vibration of the machine
by regularly maintaining it and keeping components
tight.
PERSONAL SAFETY
Never use only one hand when using the saw!
Otherwise there is a risk that operating staff, helpers or
onlookers may get injured. A chainsaw has been
designed for use with both hands.
Wear your Personal Protective Equipment (PPE),
consisting of:
Cut-resistant and non-slip safety shoes, cut-protection
trousers, highly visible vest or jacket in signal colours,
gloves and a helmet with visor and hearing protection.
When starting the chainsaw or cutting with it, no other
people should be close to you. Ensure onlookers and
animals cannot get into the working environment.
When the motor is running, all body parts must point
away from the chainsaw.
SAFETY NOTICES FOR hANDLING FLAMMABLE FUELS
WARNING!:
Petrol is easily flammable!
Store petrol in containers that have been designed
specially for this purpose.
Refill with petrol when you are outdoors, and do not
smoke.
Refill with petrol before starting the motor. Never
remove the fuel tank filler cap or refill with petrol while
the motor is running or when it is still hot.
When fuel has been spilled, do not start the motor but
remove the machine from the area of the spilled fuel
and avoid all ignition sources until all petrol fumes have
dispersed. Put the cap back securely on the fuel tank
and on the canister.
REFUELLING
Turn off the motor before refuelling.
CAUTION! Always open the fuel filler cap carefully so the
existing pressure can be released slowly.
High temperatures are generated on the casing during
work. Before refuelling, allow the machine to cool down
fully.
CAUTION! If the machine has not cooled down
sufficiently, the fuel could ignite during refuelling and
cause severe burns.
Ensure that the tank is not overfilled. If you spill any fuel,
it has to be wiped away immediately and the machine
must be cleaned.
Always close the screw plug on the fuel tank properly,
so loosening is prevented from vibrations during
operation.
DANGER!
Never refuel the machine close to an open
flame.
Always close the screw plug on the fuel tank properly,
so loosening is prevented from vibrations during
operation.
