Procopi Proswell Tropic HEXA Скачать руководство пользователя

Страница: 15 / 40

proswell.fr

INSTALLATION INSTRUCTIONS

/ OCTO / OCTO + / HEXA

Mount the wooden brackets on the long sides as shown.

FITTING THE UNDERLAY:

Important !

The ground underneath the underlay should be absolutely flat and free of any bumps or rough areas.

Because of the pressure exerted by the water, even the smallest bump will be visible underneath the liner. After clearing

the ground, spread a layer of sand mixed with cement (1 part cement to 7 parts sand) over the floor of the pool and

compact it. This layer should be no more than 1 cm deep. (The sand and cement are not supplied). Unfold the underlay

in the pool taking care to line it up correctly with the corners. Smooth out any wrinkles.

IMPORTANT !

Check that the structure is correctly assembled

before mounting the liner locking track.

To do this:

- use a spirit level to check that the structure is horizontal

around the entire periphery.

- check that the 4 diagonals are equal in length.
Fix any imperfections before continuing.

The liner locking track should be flush with the top of the

wooden structure.

Before mounting the liner locking track, pre-drill using a

Ø 3mm drill bit.

Avoid over tightening, this could cause the screws to

break through the track.

MOUNTING THE LINER LOCKING TRACK & FITTING THE UNDERLAY

Hold the track in position using a screw placed 2 cm from

each end. Then complete attachment of the track by

inserting screws at 20 cm intervals. (Use Ø4 x 35 screws

-sachet D).

Each side of the pool is fitted with one track 1.18 m long and another track trimmed to fit, see the table below.

Trim 8 tracks according to the table below. Before making the cuts, check that the total length of the track is equal to the

length of the wall less 10 cm. Use a mitre box to ensure that the cuts are clean and straight. Deburr the cuts using the

fine grain file.

Pool model

Short side

Short

side

Long side

Octo +450

1.14

1.18+1.18+0.16

Octo +510

1.18+0.26

1.14

1.18+1.18+0.57

Octo +540

1.14

1.18+1.18+0.88

Octo +610

1.18+0.26

1.18+1.18+1.18

Octo +640

1.18+0.26

1.18+1.18+1.18+0.29

Содержание Proswell Tropic HEXA









































Результаты поиска

Содержание Proswell Tropic HEXA

Отзывы:

Похожие инструкции для Proswell Tropic HEXA

Бренды по названию

Популярные бренды

Procopi Proswell Tropic HEXA, Руководство по установке

Результаты поиска

Содержание Proswell Tropic HEXA

Отзывы:

Похожие инструкции для Proswell Tropic HEXA

Бренды по названию

Популярные бренды